628921

Gude GD 20 IE 85092 Manual

30
Zoom out
Zoom in
Previous page
1/56
Next page
10
GB
SERVICE PROCEDURES
Continued
PUMP ROTOR
(Procedure if Rotor is Binding)
1. Remove upper shell (see page 7).
2. Remove fi lter end cover screws using5/16” nut-driver.
3. Remove fi lter end cover and air fi lters.
4.Remove pump plate screws using 5/16”nut-driver.
5. Remove pump plate.
6. Remove rotor, insert, and blades.
7. Check for debris in pump. If debris is found, blow out with
compressed air.
8.Install insert and rotor.
9. Check gap on rotor. Adjust to .076/.101 mm (.003”/.004”) if
needed (see Figure 25).
Note: Rotate rotor one full turn to ensure the gap is .076/.101
mm (.003”/.004”) at tightest position. Adjust if needed.
10.Install blades, pump plate, air fi lters and fi lter end cover.
11.Replace fan guard and upper shell.
12.Adjust pump pressure (see page 8).
Note: If rotor is still binding, proceed asfollows.
13.Perform steps 1 through 6 above.
14.Place fi ne grade sandpaper (600 grit) on fl at surface. Sand
rotor lightly in “fi gure 8” motion four times (see Figure 26)
15.Reinstall insert and rotor.
16.Perform steps 10 through 12 above.
A.
B.
C.
D.
E.
F.
G.
H.
SERVICE PROCEDURES
A.
B.
C.
A.
A. gap adjusting
screw
B. .076/.101 mm
(.003”/.004”) Gap
Measured With
Feeler Gauge
C. Blade
Figure 25 – Gap adjusting screw locations.
A.
A. sandpaper
Figure 26 – Sanding rotor.
A.Blade, B.Pump plate, C.Air intake fi lter, D.Filter end cover,
E.Fan guard, F.Air output fi lter, G.Rotor, H.Insert.
Figure 23 – Rotor location, 35.000 btu/Hr and 70.000 Btu/
Hr.
A.
B.
C.
D.
E.
F.
G.
H.
Figure 24 – Rotor location, 100.000 Btu/Hr.
A.Blade, B.Pump plate, C.Air intake fi lter, D.Filter end cover,
E.Fan guard, F.Air output fi lter, G.Rotor, H.Insert.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GD 20 IE 85092 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GD 20 IE 85092 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info