628919
31
Zoom out
Zoom in
Previous page
1/56
Next page
11
GB
FAN
IMPORTANT: Remove fan from motor shaft before removing
motor from heater. The weight of the motor resting on the fan
could damage the fan pitch.
1. Remove upper shell (see page 7).
2.Use 1/8” allen wrench to loosen setscrew which holds fan to
motor shaft.
3. Slip fan off motor shaft.
4. Clean fan using a soft cloth moistened with kerosene or
solvent.
5. Dry fan thoroughly.
6. Replace fan on motor shaft. Place fan hub ush with end of
motor shaft (see Figure 28).
7. Place setscrew on at of shaft. Tighten setscrew rmly 4.5 to
5.6 N-m (40 to 50 in-lbs).
8. Replace fan guard and upper shell.
IGNITION CONTROL ASSEMBLY
WARNING: Unplug heater before servicing.
Remove Old Assembly
1.Using the 5/16” nut driver or socket wrench, remove the four
side cover screws (see Figure 29).
2. Disconnect the nine wires from the ignition control assembly.
3. Using needle nose pliers, squeeze the tab on the printed
circuit board support and lift up on the edge of the ignition
control assembly (see Figure 30). Repeat this for the other
four printed circuit board supports then remove the assembly.
Installing the New Assembly
CAUTION: Ignition control assembly contains
electrostatic components. Handle the assembly by the
edges of the printed circuit board. Do not touch any of
the quick connect terminals or electronic components.
1. Align the ve holes in the assembly with the ve printed circuit
board supports in the side cover.
2.Holding the assembly by the edges of the printed circuit
board, apply downward pressure until all ve tabs on the
printed circuit board supports springlock into place. Pull up on
assembly to verify this (see Figure 31).
3.Connect the nine wire leads to the ignition control assembly as
shown in the wiring diagram on page 17.
CAUTION: Double check connections. Connecting
ignition control assembly wrong could result in damage
to the ignition control assembly and/or other components
in the heater assembly.
4. Using the 5/16” nut driver or socket wrench reinstall side
cover to heater. Tighten screws until snug. Do not over torque!
SERVICE PROCEDURES
A.
B.
C.
A.
B.
C.
D.
Figure 27 – Fan, motor shaft
and setscrew location.
A.Fan, B.Motor shaft, C.Set screw, D. Flush.
Figure 28 – Fan cross
section.
A.
A. Side cover
Figure 29 – removing cover.
A.
B.
C.
A. Side cover
B. Ignition Contro l As-
sembly
C. Printed Circuit
Board Supports (5)
Figure 30 – Removing circuit board
A.
B.
A. Unacceptable
B. Acceptable
Figure 31 – Attaching Circuit Board toTabs.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GD 10E 85090 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GD 10E 85090 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info