628919
26
Zoom out
Zoom in
Previous page
1/56
Next page
6
GB
TROUBLESHOOTING
Continued
FAULT CONDITION POSSIBLE CAUSE REMEDY
Heater ignites but ignition control
assembly shuts heater off after a
short period of time (ON/OFF switch
light remains on)
1.Pump pressure incorrect
2. Dirty air intake, air output, and/or lint
lter
3.Dirty fuel lter
4. Obstruction in nozzle assembly
5. Photocell assembly not properly installed
(not seeing the ame)
6. Dirty photocell lens
7. Bad electrical connection between
photocell and ignition control assembly
8. Defective photocell
9. Defective ignition control assembly
1. See Pump Pressure Adjustment, page 8
2. See Air Output, Air Intake, and Lint Filters,
page 8
3. See Fuel Filter, page 6
4. See Nozzle Assembly, page 8
5. Make sure photocell boot is properly
seated in bracket
6. Clean photocell lens
7. Check electrical connections. See Wiring
Diagram, page 17
8. Replace photocell
9. Replace ignition control assembly
ON/OFF switch light does not come
on when switch is turned to the ON (|)
position and heater does not start
1. No power to heater
2. Bad electrical connections
3. Electrical short in ignitor
1. Verify that power cord is plugged into an
electrical outlet and that the circuit breaker
in the electral panel is reset
2. Check electrical wiring and connections.
See Wiring Diagram, page 17
3.Check ignitor wiring. If no problems are
found, replace ignitor (see page 7)
ON/OFF switch light comes on when
switch is turned to the ON (|) Position
but turns off after ve seconds
1. Electrical short in motor 1.Check motor wiring. If no problems are
found, replace motor
WARNING: High voltage!
WARNING: High voltage!
SERVICE PROCEDURES
WARNING: Never service heater while it is plugged in,
operating, or hot. Severe burns and electrical shock can
occur.
UPPER SHELL REMOVAL
1. Remove screws and lock washers along each side of heater
using 5/16” nutdriver. These screws attach upper and lower
shells together.
2. Lift upper shell off.
3. Remove fan guard.
FUEL FILTER
(35.000 and 70.000 Btu/Hr Models)
1. Remove side cover screws using 5/16”nutdriver.
2. Remove side cover.
3. Pull rubber fuel line off fuel lter neck.
4. Carefully pry bushing and fuel lter out of fuel tank.
5.Wash fuel lter with clean fuel and replace in tank.
6.Attach rubber fuel line to fuel lter neck
7.Replace side cover.
FUEL FILTER
(100.000 Btu/Hr Models)
1. Remove side cover screws using 5/16”nutdriver.
2. Remove side cover.
3. Pull upper fuel line off fuel lter neck.
4. Carefully pry bushing, lower fuel line, and fuel lter out of fuel
tank.
5. Wash fuel lter with clean fuel and replace in tank.
6. Attach upper fuel line to fuel lter neck.
7.Replace side cover.
Continued
TROUBLESHOOTING
SERVICE PROCEDURES
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GD 10E 85090 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GD 10E 85090 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info