Manual Gude GAK 600 T 94012 (page 11 of 43) (English, German, Dutch, French, Italian)

627634

Zoom out

Zoom in

1/43

chain should stop if the starter is tripped. Have defective

switches replaced in an authorised servicing centre.

• Pruning should be tried/trained on wood cutting rack

• Do not use the pole pruner in windy weather or in a

storm.

• Watch out for falling prunes and limbs. Check the tree

before pruning. Make space for the branches.

• Do not use the pruner to cut annual shoots and shrubs.

• Do not stand on a ladder or another unstable aid when

using the pruner Use both your hands when working with

the pruner Force the tool in a firm sustained manner. Do

not use the pruner to cut the branches, diameter of which

is bigger than that of the guide bar.

• The others should be kept out of reach of the pruner

cutting end – and at a safe distance from the workplace

• The pole pruner is not insulated! Do not use the pruner in

proximity of cable, electric or telephone lines. In result of

a voltage peak, the operator may get exposed to a fatal

risk! Always stand off at a distance of 10 meters from any

electric line. Observe the local regulations.

• Never stand directly under the branch that is being cut.

Always stand away from the falling branches path.

Use the Electrical Branch chainsaw on the mains with

an undercurrent protection switch (FI)!

Behavior in case of emergency

Perform necessary first aid measures according to the injury

and call for medical attendance as soon as possible.

Prevent the injured against any further injuries and calm him

down.

Intended use

Electrical Branch Güde chainsaw is intended for

pruning/trimming of the tree branches. Failure to observe the

provisions of the generally applicable regulations and the

provisions of this manual, the manufacturer can not be held

responsible for any damage made.

Unpacking

1. Remove the separate parts of the pruner from the outer

cardboard.

2. Check the parts for the damages from transportation. If

any damaged or defective parts are found out, advise the

dealer, from whom you bought the pruner.

Disposal

The hints over disposal result from the pictograms which are

applied on the product and the packing. A description of each

pictogram can be found in the chapter “markings on the

product“.

Requirements for the operator

The operator should have read the operating manual carefully

before using the product.

Qualification

Besides a detailed training through a skilled staff, no special

qualification for the use of the product is necessary.

Minimum age

The product may not be operated by people, who are less than

16 years old.

The use by young people forms an exception, if the operation

takes place during a vocational training to achieve the skill and

under supervision through a trainer.

Training

The use of the product requires only a corresponding training

through a skilled staff or on the basis of the operating manual.

A special training is not necessary.

Technical data

GAK 600 T

Connection : 230V

Frequency : 50 Hz

Protection type : IP 32

Protection class : ll

Max. output : 600W / P1

Guide bar length : 240 mm

Total length : 2,1 – 3,0 m

Cutting length 180 mm

Oil tank : 0,2 l

Connection cable : 300 mm

Acoustic output level : 103 dB

Wight : 5 kg

Order No. : 94012

Transport and storage

If the Electrical Branch chainsaw is to be stored for a period

above 30 days, steps described below should be taken:

1. Empty the oil tank.

2. Remove and clean the guide bar and the chain. Clean the

guide bar and the chain by dipping it in kerosene solvent

or fine soap solution.

3. Dry the guide bar and the chain.

4. Put the chain in a tank filled with oil to prevent corrosion.

5. Apply a thin oil layer on the guide bar.

6. Wipe the Electrical Branch chainsaw interiors with soft

cloth wetted with fine soap solution.

7. Store the Electrical Branch chainsaw at an elevated

locked place out of the reach of children.

8. Store the Electrical Branch chainsaw in a plastic bag at a

dry place or put a cover on the guide bar.

Terms and definitions

Guide Bar: A metal rail rising above the unit body. The guide

bar supports and guides the chain.

Backlash: A dangerous backlash may occur when the guide

bar tip top quadrant touches an object while the chain is

moving. The guide bar is suddenly shot up and then in the

direction of the operator

Oil Lubrication System: The guide bar and chain lubricating

system

Saw Chain (chain): A chain loop with saw teeth cutting the

wood. The chain is motor-driven. The chain leans against the

guide bar.

Sprocket wheel: a tooth gear driving the chain.

Switch: a device closing and opening the electrical circuit to

the saw motor.

Switch lock: A device to prevent switching when the unit is

unattended.

Starter: a device that will switch the unit on and off. The

pruner will switch on by pushing the starter, and off by tripping

it.

Limbing/Trimming /Pruning: Branch cutting procedure on a

standing tree.

Underhand Cut: a cut conducted from a lower part of the stem

or a branch. It shall be done cutting by the guide bar tip in a

regular cutting position.

Commissioning

Guide bar and saw chain installation

Warning: Chain cutting edges are sharp. Wear

protection gloves to handle the chain.

Important notice: For installation, fasten the pruner in a

vice.

1. Remove the sprocket wheel cover. (Fig. 5)

2. Fit the chain on the guide bar (mind the chain motion

direction Fig 9!)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude GAK 600 T 94012 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude GAK 600 T 94012 Manual

Product: