Manual Gude GAB 8A 85060 (page 9 of 56) (English, German, Dutch, French, Italian)

628817

Zoom out

Zoom in

1/56

Introduction

To enjoy your new battery charger as long as possible,

please read carefully the Operating Instructions and the

enclosed safety instructions before putting it into operation.

Further, it is recommended to keep this manual for future

reference – when features of this product are required to

be recalled. Because of the continuous development of our

products, we reserve the right to make technical changes.

This document represents the original Operating

Instructions.

Appliance description

The automatic battery charger is controlled by a micro

processor and as a consequence, charging takes place in

three levels. At the first level, the battery is charged by

almost constant current to approximately 85%. At the

second level, the battery is charged to approximately 95%

at constant voltage. The third level keeps constant voltage

of the battery, i.e. the battery is constantly charged to the

full extent.

GAB 15A (pic. A)

1. Carrying handle

2. Operating panel

3. Charging pliers, black (-)

4. Charging pliers, red (+)

5. 12V DC outlet

GAB 8A (pic. A)

1. Carrying handle

2. Operating panel

3. Charging pliers, black (-)

4. Charging pliers, red (+)

5. Power cord

GAB 15A operating elements (pic. B)

1. Voltage indication LED

(LED is on when the appliance is in the standby

mode or if the 2/8/10/15A button has been

pressed)

2. 2/8/10/15A charging current setting button

(One second after pressing, the appliance starts

to be charged by appropriate charging current

with the existing value being shown on the

display)

3. ON/OFF button

(Keep the button pressed for at least 1 second –

this will switch the appliance on and “000“ will be

blinking on the display – now you are in the

standby mode)

4. 12V DC outlet button

ON/OFF with signalling by LED

(Pressing the button in the standby mode

activates the 12V DC outlet on the back of the

appliance. If the button is pressed again, the

charger gets back to the standby mode).

5. Button for current battery voltage

(After pressing the button, the appliance shows

the current battery voltage for 3 seconds in the

standby mode and during the charging process.)

6. "Battery fully charged" LED

7. "Battery charging" LED

8. "Failure" LED

9. Three-digit LED display

(see the table for description)

10. LED signalling current

(this LED is on during the charging process or

when the 12V DC outlet is active)

11. LED for WET type battery

12. LED for AGM type battery

13. LED for GEL type battery

LED display

Description Failure removal

Standby mode

Check the battery

Battery voltage is

shown during the

charging process or

in the standby

mode, e.g. 13.8 V

1. Charging current

is shown (e.g. 5.8 A

);

2. Extraction flow at

12V DC outlet is

shown.

1. Battery pole not

connected

2. Short circuit

1. Connect the

battery pole.

2. Faulty battery

Exchange of

connections

(reversal of polarity)

Switch the

appliance off and

disconnect the

plug from the

outlet and connect

correctly

1. Battery is

significantly

discharged

2. Faulty battery cell

3. 3.6 V battery is

connected

Switch off and

disconnect from

the electric power

supply and

remove the battery

(faulty)

1. Battery cell short

circuit

2. Inappropriate

charging current has

been selected

Try another

charging current, if

the failure

persists, the

battery is probably

faulty

Battery terminal has

got released, the

appliance is

switching off and

activating the

warning signal

Check the

connection and

select the

charging current

again

Battery is fully

charged, battery

voltage remains

constant, battery

remains charged.

BATTERY VOLTAGE

CHARGING CURRENT

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude GAB 8A 85060 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude GAB 8A 85060 Manual

Product: