623628

Gude DHH 1050-7 T ECO 01955 Manual

18
Zoom out
Zoom in
Previous page
1/119
Next page
Operation
1. At low temperatures, have the machine idling for about 15 minutes for the oil to get warmed to the required
temperature.
2. Lay a piece of wood to be cleaved on the table and hold it to the lever using anchoring wires/grabs.
3. Start cleaving pushing both the levers downward.
4. With cleaving completed, lift one lever at least, the cleaving column will go up automatically.
It is strictly forbidden for two persons operate the machine at a time, when one would hold the wood and the
other one would operate the wires/grabs. Never block the lever (anchoring wire/grab).
Stroke adjustment
With pieces up to ca 50 cm long or a bigger quantity, it is possible to
increase the working capacity by making the cleaving knives reverse
shorter.
Model DHH 1050/6TC with control rod
Procedure is as follows:
Lay a short piece of wood on the table, lower the knife down to be at a
distance of ca 2 cm above the piece and put the machine off (push red
button on the switch and unplug). Now, you may adjust the reverse run
using the side rod fixing the rod at a required height with an adjusting
screw.
Hydraulic Connection
Hydraulic hoses and joints shall be checked for leakage every 4 hours of operation
and retightened if necessary.
Hydraulic oil/tank
Common hydraulic oil may be replenished in all cleaving machines (HLP 46 e.g.)
or another product of the same viscosity. Oil change is not necessary .
Type DHH 1050/ 7 T/ MBS: tank ca 6 litres
Transport Directions
Transport
All cleaving machines have large wheels. To move the machine, hold the cleaving column lug with one hand and the lug
above the motor with the other hand and tip the machine slightly over to your body. Once in this position, the machine
may travel easily.
Never transport the cleaving machine in horizontal position to prevent
any leakage of fuel and hydraulic oil.
For transport, move the cleaving knife down completely.
Lärminformation
Type DHH 1050/7 T ECO/ idle run ca 67 dbA = full load ca 86 dbA
18
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude DHH 1050-7 T ECO 01955 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude DHH 1050-7 T ECO 01955 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 8,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info