624553

Gude DHH 1050-11 T ECO 02012 Manual

26
Zoom out
Zoom in
Previous page
1/173
Next page
Open the fuel tap
Put the engine switch to the “ON“ position (pic. 3)
Make sure the engine is cold when being started.
Turn on the engine choke (pic. 4; pos. “CHOKE“)
Turn the speed control lever (pic. 4; pos. “START“) to full speed.
First, pull shortly the starting cable so that it is stretched. Now pull the starting cable slowly to the stretched
position with your left hand resting on the engine and one more strong pulling the starting cable. Turn the
engine choke off as soon as the engine gets started (pic. 4; pos. “RUN“)
Give full throttle using the speed control lever (pic. 4; pos.”HARE”)
To be provided
The starting cable must not reel automatically. It must always be reeled back by hand. If the engine fails to
start even after several attempts, check whether the tank has been refuelled properly. Maybe there is too
much fuel in the roll, which has caused the spark plug to get damp.
Switching off the engine
Put the speed control level to the idle gas position (pic. 4; pos. Želva).
Use the engine switch (pic. 3; pos. “OFF”) to switch off the engine. Never leave the appliance unattended
when the engine is running. Never switch the engine off when the choke is on as the engine could get
damaged. Close the fuel tap (pic. 2; pos. “OFF“). Pull slowly the starter handle until you feel resistance. By
this, valves get closed.
This step is necessary to prevent moist air from entering the combustion chamber from outside.
1. Put the wood to be split on the table as short or long logs and set the backward movement
accordingly (see Lift setting).
2. Now clasp the split wood with both operating arms (see Stop screw setting) and press them down
at the same time.
3. Remove the split wood from the working area and put another wood on the table.
4. If the splitting knife is greased from time to time, more difficult wood can also be split.
Start the splitter and wait until the splitting column gets to the starting position.
Now press both operating levers to make the splitting column go down. Press just the right or left operating
lever in turn. If the splitting column stands each time, you can use the splitter with no worry.
.
If the splitting column keeps going down, the two-hand operation must be subject to new
calibration.
For that purpose, contact an authorised workshop.
V nebezpečných situacích a při nehodách musíte dát páku pro regulaci otáček co možná nejrychleji
do polohy „STOP“ a motor vypnout spínačem motoru (obr. 3; poz. „OFF“).
Hydraulic
Hydraulic
Hydraulic hoses and joints need to be checked for tightness after app. 4 hours of operation and
tightened if necessary.
Hydraulic oil/tank
Regularly sold hydraulic oil (e.g. HLP 46) or any other product of identical viscosity can be used for all
splitters.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude DHH 1050-11 T ECO 02012 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude DHH 1050-11 T ECO 02012 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 10,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info