624544

Gude DHH 1050-10 TP 02004 Manual

28
Zoom out
Zoom in
Previous page
1/92
Next page
24
GB
ENGLISH
• The machine meets the EN 61000-3-11 require-
ments and is subject to special connection condi-
tions. That means that a use on optional points of
connection is not allowed.
• The machine may cause temporary voltage uctua-
tion in adverse conditions.
• The machine has only been designed to be used on
points of connection not exceeding the maximum
allowable network impedance Zmax = 0.233 .
• As a user, you must make sure, after consultation
with your energy provider, if necessary, that your
point of connection on which the machine is to be
operated meets the requirements above.
Working area
For safe wood splitting, it is essential that the wor
-
king area is at and slip-resistant and that a sucient
sp
ace for moving is provided. To take the wood
splitter to your home, it is necessary there are no
obstacles in the way, i.e. no risk of tripping. Adequate
lighting of the working area needs to be provided.
Work preparation
Before putting the machine into operation, working
of the safety guards (two-lever operation system, in
particular) must be checked.
• Put both control levers down and the splitter knife
do
wn, app. 5 cm above the desk.
• One control lever to be released at all times, with
the splitter knife remaining in the selected position.
CAUTION! Whenever the machine is to be put into
operation, make sure the splitter desk is rmly and
safely tted to the machine.
operation
Power supply must be interrupted by pressing the
red button on the switch and unplugging the machi
-
ne for any repair or servicing work or when leaving
the wood splitter. Turning to the O position is not
enough to interrupt the power supply.
Using the wood splitter may lead to some hazards.
Therefore, the machine may only be handled by
instructed and experienced persons. The operator
must wear close-tting clothing and safety shoes.
Residual risks
Dry and dried-up wood may jump up when
being split and injure the face of the operator.
Adequate protective clothes to be worn!
Wooden pieces produced during splitting
may fall down and injure legs of the operator.
Make sure there are no persons in the
working area during operation or make
sure such persons keep a sucient
safety distance.
The wood splitter has been designed to
be operated by 1 person. The machine
must never be operated by two or more
persons.
Wood splitter being operated by two persons,
with one holding a piece of wood and the other
controlling the clamps is strictly prohibited.
Do not use this product in any other way as stated
for normal use. Not observing general regulations
in force and instructions from this manual does not
make the manufacturer liable for damages.
Safety Instructions
Electrical connection
WARNING! Electric shock! There is a risk of
an injury caused by electric shock!
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Check the voltage. Technical data given on the type
label must correspond with electric network voltage.
Insert the plug of the electrical cable in a socket of
suitable shape, voltage and frequency complying
with current regulations.
Only for 400 volt machines: It is essential to respect
the engine rotation direction (see the arrow on the
engine) as operation in wrong direction would da-
mage the oil pump. Warranty claims cannot apply in
su
ch a case. Change the rotation direction by turning
the connector polarity if necessary.
Pursuant to the provisions of „CE“ professional
associations, etc., all splitters are tted with an
undervoltage release in the switch. This will prevent
accidental repeated starting in case of current inter-
ruption due to power failure, accidental unplugging,
de
fective fuse, etc. The machine must necessarily be
turned on again by repeated pressing of the green
switch.
Wilful holding or blocking of the switch, unless being
a neutral, will automatically lead to switch failure.
IThe warranty will not apply in such a case that must
naturally be checked.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude DHH 1050-10 TP 02004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude DHH 1050-10 TP 02004 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 5,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info