Manual Gude 94062 GH 2600 P (page 18 of 57) (English, German, Dutch, French, Italian)

627495

Zoom out

Zoom in

1/57

Do never attempt to change engine revolution settings. In

case of problems, contact a specialist.

Keep ventilation holes without residues and other deposits

to avoid engine damage and potential fire.

Do never lift or remove the appliance if it is on and

running.

Turn the appliance off, wait until the cutting mechanism

stops, and unplug the appliance every time you leave the

workplace.

Do never tilt the appliance during operation.

Do never expose the appliance to rain and moisture. Store

the appliance on a dry place only.

Do never attempt to disengage the forced turning off.

Application according to intended use

The appliance is intended for shredding of fibrous and

woody garden waste for composting purposes. Collection

bag or collection box is intended only for collection of

shredded material (not for storing). Do never stand on the

collection box.

Any other use contradicts to the intended use.

Manufacturer is not responsible for subsequent damage

and injuries. Please note the appliance is intended for

domestic use only.

Assembly GH 2600 P #94062 (Fig. B/C)

Assembly GH 2600 #94064 (Fig. F/G)

Attention! Turn off and unplug the appliance before

maintenance, cleaning and assembly. The same

procedure applies to damaged, cut or tangled cable.

Keep power supply voltage: power supply voltage must

correspond to data on the appliance product label.

Small conductor size of the extension cable significantly

reduces power output of the appliance. For cables up to 25

metres, minimum cross section is 3 x 1.5mm², for cables

over 25 metres, minimum cross section is 2.5mm².

Attention! The extension cables not corresponding to the

requirements must not be used. The extension cable, plug

and socket must be water-proof and approved for outdoor

application.

Cable connections must be dry and must not rest on

ground.

If a cable drum is used, it must be unreeled.

For GH 2600 P #94062, proceed as follows:

(Fig. B/C)

• Unpack the appliance and assemble the tube

frame of the appliance (Fig. B).

• Now, assemble the carriage and transport

wheels (Fig. C).

For GH 2600 P #94064, proceed as follows:

(Fig. F, G)

• Unpack the appliance (Fig. F/2 and F/3)

• Take the collection box and attach legs to the

appliance (Fig. F/4 and F/5)

• Attach the carriage and transport wheels (Fig.

F/6 and F/7).

• Put the appliance body on the base (Fig. G/8)

(adhere to Fig. G/8-1 and G/8-2 ).

• Now, attach the appliance to the base. (Fig. G/9)

• Put the collection box under the appliance (Fig.

G/10) and secure by the collection box clamping

lever (G/10-1 a G/10-2). Attention! The

appliance does not operate without clamping!

Operation

Always put the appliance on solid and leveled surface. Do

never tilt or move the appliance if it is on and running.

Attention! The engine runs down after turning off.

Remove soil from the root balls and avoid penetration of

foreign objects such as stones, glass, metals, plastic

materials or textiles in the filling hopper and thereby to the

appliance, cutting roll; the appliance may get damaged.

The filling hopper must be empty.

Turning on

Press green Start pushbutton (Fig. A/3) or

(Fig. E/2)

Turning off

Press red Stop pushbutton (Fig. A/3) or

(Fig. E/2)

Safety feature against repeated running up

The safety feature against repeated running up prevents

sudden engine start after power supply failure.

Reverse operation

Press and hold the reverse operation button (Fig. A/4),

(Fig. A/4a) and depending on your model, press also

green Start button (Fig. A/3) or (Fig. E/2), the cutting roll

then rotates in reverse direction and releases the clogged

material.

Overload safety feature

If the appliance is exposed to excessive load (e.g. clogging

of cutting roll), the appliance halts after several seconds.

Work instructions

Material supply

Insert the shredded material only, the rotating cutting roll

will draw it in automatically.

• Insert such quantity of material not to clog

the hopper.

• Do not shred soft waste without solid

consistency but compost it directly.

• Make sure the shredded material exits to the

collection box or bag without any

restrictions - danger of clogging!

• Best results are achieved if you shred fresh

branches shortly after cutting.

Adjustment of pressure plate

The pressure plate is calibrated by the manufacturer and

requires no adjustment before first commissioning.

Adjustment of the pressure plate is required in case of

wear, e.g. when the branches wedge in chain each other

and they can not be shredded correctly.

In this case proceed as follows:

Turn the engine on and slowly rotate the adjustment knob

(Fig. A/9 or Fig. E/6) or Fig. H/13 clockwise to hear slight

friction. The cutting roll sharpens the pressure plate to

correct distance. Adjust the plate so that it is not worn too

early.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude 94062 GH 2600 P in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude 94062 GH 2600 P Manual

Product: