Manual Gude 85056 (page 13 of 19) (English, German)

628861

Zoom out

Zoom in

1/19

 Screw the closing nut on the connecting tread (left

thread) – put the protective cover on.

 Connect the new cylinder and check tightness.

Start up procedure / discontinuation or stopping procedure of

the catalytic stove:

 Before operation, let the cylinder stand in a vertical

position for 1 hour if transported so the elements

more burdening to the environment may settle down

to the bottom of the cylinder.

 Place the gas cylinder to the inner space of the

device (back side). Connect the gas cylinder as

described above.

 Open the cylinder valve on the propane cylinder by

turning to the left.

 Push the large setup button down and turn it to the

large flame symbol – start.

 Push the piezo-ignition button several times, to light

the starting flame. When the starting flame is visible,

keep the setup button pushed for about 20 seconds,

heating up the thermal element. You can release the

setup button afterwards and the heating is turned on

to the highest level. If the starting flame goes off,

though, repeat the procedure.

 The heating output can be lowered by pushing lightly

on the setup button and turning it to the medium or

minimum flame symbol. We recommend to wait for 10

minutes after starting the operation before changing

the heating output.

 The catalytic gas plate is slightly hot only in the area

of the starting flame, but the full heating output is

spread over the whole catalytic plate.

 The slight smoke (fresh paint) will dissipate after

heating up.

CAREFUL! Do not move when hot (transport).

 The gas cylinder must not be turned during the

operation or shut down of heating device. The highest

danger of accident!

 Shutting off of the catalytic gas heating device:

CLOSE THE GAS VALVE ON THE CYLINDER.

Illustration 3:

The devices are supplied with an electric heating ventilator

allowing for an increase of 2 x 1000 W as an addition to

the regular gas burning by the device.

 Electric power supply cable (rolled up inside the

device) (1) should be connected to a socket of 230V-

50Hz.

 Push the heating ventilator switch. There are 4

positions of the switch: (2)

= ventilator off

= ventilator only

= ventilator + 1000 W

= ventilator + 2000 W

Inspection and maintenance

 Any dirt on the case of the device can be cleaned off

with a wet towel. Water must not get onto the surface

of the catalytic burner.

 Do not use any abrasive cleaning means or solvents

for cleaning.

 In case of a longer discontinuation of use, disconnect

the gas cylinder and place it outside of the device,

store the device in a dust-free environment.

 Contact your contractual sales point for more

extensive maintenance.

 Use only original spare parts for repairs.

 Such maintenance should be performed at least once

every 2 to 3 years.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude 85056 in the language / languages: English, German as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude 85056 Manual

Product: