624846

Gude 58011 Li-Ion 108 Manual

8
Zoom out
Zoom in
Previous page
1/34
Next page
Check whether the screwdriver bit is fitted properly
before putting the appliance into operation.
Do not try to change the engine speed setting. Contact a
professional in case of problems.
Before drilling holes to a wall, make sure you are not
going to strike electric current, gas or water using a current
seeker if necessary.
Application according to intended use
Suitable for screwing and loosening of screws and drilling
to wood, metals and plastic materials.
Any other use contradicts to the intended use.
Manufacturer is not responsible for subsequent damage
and injuries. Please note the appliance is intended for
domestic use only.
Before putting into operation
The accumulator is supplied partially charged. It must be
charged to full extent before it is put into operation for the
first time.
CAUTION:
• Charge the accumulator only using a charged
included in the supply.
• Use only sharp drills and screw bits that are in a
perfect and appropriate condition.
• When drilling and screwing to walls, check whether
there are no electric lines or water piping or gas lines
in the wall.
Operation
Accumulator charging:
1. Disconnect the accumulator from the appliance by
pressing the snap button (pic. 1/8) and pull the
accumulator down.
2. Now compare the voltage on the charger type label
with the voltage of your electrical network.
3. Plug the charger and connect the charger cable with
the charger connector.
#58011:
4. Red LED diode is on when the accumulator is being
charged (pic. 1/10)
5. Green LED diode is on after charging is complete
(pic. 1/10)
#58014:
4. Green LED diode is on after plugging the charger.
5. Red LED diode is on during the charging process.
The red LED diode then starts “blinking“.
6. The charging process is complete when the red LED
diode turns off.
To ensure long service life of the accumulator, timely
charging should be provided at all times.
If the accumulator is shortly before being discharged, it
switches off. In any case, do not use the cordless
screwdriver any more. Doing so could dramatically reduce
the service life of the accumulator.
Torque adjustment:
Torque can be adjusted depending on the size of screws
on the torque adjustment device (pic. 1/1).
Torques depends on a number of factors:
• Type and hardness of material you are working with.
• Type and length of the screws that are used.
• Requirements imposed on the screwed joints.
Adjust the torque only when the cordless
screwdriver is idle.
Drilling:
To drill, adjust the torque (pic. 1/1) to the final “drilling“
level.
Level switching:
Switch only when the cordless screwdriver is idle.
• Screwing level
lower speed, higher torque.
• Drilling level
Higher speed, lower torque.
Rotation direction switching:
The rotation direction may be adjusted by the shift switch
(pic. 1/3). You can choose between the right and left
rotation. To prevent damage of the gearing, the rotation
direction may only be changed when the appliance is idle.
If the switch is in the central position, On/Off is blocked.
On/Off:
The more this switch (pic. 1/4) is pressed, the higher the
cordless screwdriver speed.
Accumulator capacity signalling:
#58011: After pressing On/Off (pic. 1/4), LED diodes (pic.
1/10) show the accumulator charging level.
#58014: After pressing the button next to the accumulator
capacity signalling, LED diodes (pic. 1/10) show the
accumulator charging level.
• All LED diodes are on
: accumulator is charged to full
extent.
• Yellow and red LED diodes are on:
accumulator is
charged to sufficient extent.
• Red LED diode is on:
accumulator is almost
discharged - charging necessary.
Tools changing:
When working on the cordless screwdriver,
adjust the rotation direction switch (pic. 1/3) to the
central position.
1. Screw the chuck (pic. 1/2) out to remove the tool.
2. Now choose the appropriate tool and insert it as deep
in the hole as possible.
3. Screw the chuck tightly again and check whether the
tool is fitted tightly.
LED light:
LED light (pic. 1/9) enables additional lighting of the
screwing or drilling space. LED light is immediately
switched on after pressing On/Off.
Identification
Product safety:
The product complies with
relevant EU standards
Prohibitions:
Protect against rain and
moisture!
Warning:
Warning/caution
WARNING! Rotating
appliance poses the risk of
injury!
8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude 58011 Li-Ion 108 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude 58011 Li-Ion 108 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info