Manual Gude 3000 85027 (page 12 of 71) (English, German, Dutch, French, Italian)

628858

Zoom out

Zoom in

1/71

Safety prevention means:

• Touch protection at the device should prevent fire

and burns; no part of the protection can be taken off

permanently.

Full protection is not provided for children and ill

persons!

• The heating device is equipped with a low-oxygen

safety device. If a higher concentration of carbon

dioxide (CO2) is detected in the room, the safety

device will automatically shut the appliance off. The

appliance cannot be turned back on until the room is

ventilated properly.

• After use of the heating device, the cylinder valve

must be turned off!

Operation

After having read the general safety instructions and

the device-specific safety instructions and having

understood them, you can start operating the device.

Follow these instructions:

Installation of the gas cylinder:

• The device uses a mixture of propane and butane

under pressure of 50 mbar.

• To operate the device, a gas cylinder with liquid gas

of max. 11 kg of filling is necessary, the hose is pre-

installed.

• Gas regulator must be selected and/or purchased

first of all, depending on the purpose of use.

• Installation or change of cylinder with liquid gas must

be performed in non-flammable atmosphere.

• When the device is not in use and during change

of the cylinder, the device valve must be turned

off.

• After the first and before any subsequent putting into

operation and especially after each bottle change, a

leak test using foamy solution (e.g. soapy water)

must be carried out.

• Tightness is proven when no bubbles appear.

It is strictly forbidden to check tightness by open

flame!

• The cylinder must be placed in such a position so that

it is not in contact with the sheet metal of the burner

and the gas supply attached to it. The hose must not

touch (be in contact with) the hot back side of the

burner.

• The device is supplied with a 40 cm long hose. The

hose must not be shortened or exchanged for a

longer one.

• Inspect the condition of the hose regularly, at least

during each change of the cylinder.

• In case of damage to the hose, it must be replaced

with a hose of the same construction, tested

according to DIN DVGVV.

• Connection of the hose to the regulator must be done

with minimum of V4" left thread. The screw spanner

SW 17 is required for installation.

• Twisting or distortion of the gas hose during the

installation of the hose and pressure regulator to the

liquid gas cylinder is not permissible.

Warning! The hose must not touch (be in contact

with) the hot back side of the burner!

• Operation with pressure regulators other than those

prescribed above is prohibited.

• Make sure the hose and regulator are changed after

5 years at the latest.

Connection of the liquid gas cylinder:

• Take the protective cover of the valve off.

• Take the covering nut from the attachment socket off

by turning (right).

• Check the rubber seal in the cylinder valve (regulator

connection).

• The regulator and the hose must be screwed on

tightly (left thread). No not use any tool or instrument.

Do not turn the regulator but the sleeve nut.

• Check the tightness of the connection.

Change of the liquid gas cylinder:

• Close the cylinder valve

• Unscrew the regulator.

• Screw the closing nut on the connecting tread (left

thread) – put the protective cover on.

• Connect the new cylinder and check tightness.

Start up procedure / discontinuation or stopping procedure of

the catalytic stove:

• Before operation, let the cylinder stand in a vertical

position for 1 hour if transported so the elements

more burdening to the environment may settle down

to the bottom of the cylinder.

• Place the gas cylinder to the inner space of the

device (back side). Connect the gas cylinder as

described above.

• Open the cylinder valve on the propane cylinder by

turning to the left.

• Push the large setup button down and turn it to the

large flame symbol – start.

• Push the piezo-ignition button several times, to light

the starting flame. When the starting flame is visible,

keep the setup button pushed for about 20 seconds,

heating up the thermal element. You can release the

setup button afterwards and the heating is turned on

to the highest level. If the starting flame goes off,

though, repeat the procedure.

• The heating output can be lowered by pushing lightly

on the setup button and turning it to the medium or

minimum flame symbol. We recommend to wait for

10 minutes after starting the operation before

changing the heating output.

• The catalytic gas plate is slightly hot only in the area

of the starting flame, but the full heating output is

spread over the whole catalytic plate.

• The slight smoke (fresh paint) will dissipate after

heating up.

CAREFUL! Do not move when hot (transport).

• The gas cylinder must not be turned during the

operation or shut down of heating device. The highest

danger of accident!

• Shutting off of the catalytic gas heating device:

CLOSE THE GAS VALVE ON THE CYLINDER.

Servicing

Do you have any technical questions? A claim? Do you

need spare parts or the Operating Instructions?

You will be helped quickly and without needless

bureaucracy at our webpage www.guede.com in the

Service part. Please help us be able to assist you. To be

able to identify your appliance when claimed, we need to

know its serial No., order No. and year of production. All

these details can be found on the type label. Enter the

details below for future reference.

Serial No.:

Order No.:

Year of production:

Tel.: +49 (0) 79 04 / 700-360

Fax: +49 (0) 79 04 / 700-51999

E-Mail: support@ts.guede.com

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude 3000 85027 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude 3000 85027 Manual

Product: