628792

Gude 2T 18016 Manual

7
Zoom out
Zoom in
Previous page
1/48
Next page
GB
!!! Please read this instruction for operation carefully before putting the machine into operation !!!
A.V. 2 Surplus print even in shortened version requires permission.
Technical changes reserved. Illustrations used represent examples.
Signs on Unit
Meaning of Symbols
Symbols shown below are used throughout this manual
and/or on the unit:
Product Safety:
Product compliance with
respective EU standards
Warning:
Warning/Caution
Beware of the hand
injury/nipping
Beware of stumbling
Keep sufficient distance from
persons standing nearby.
Environment Protection:
Do not throw the packaging
material away, arrange its
proper disposal.
The packaging material from
the cardboard can be
handed in into a
corresponding collection
point.
Packaging:
Protect from moisture Keep Up
Interseroh-Recycling
Technical specifications:
Max. carrying capacity height mm
Weight
Unit
A premium quality hydraulic cylinder, a large pedal of special
cast iron to add the stability,
a freely movable tilting lift lever,
2-part lifting lever, dimensionally fitting, to control the valves,
supporting plate, screwing support.
Machine description
Fig. 1:
1. Vehicle lifting jack
2. Two-part lifting lever
Fig. 2:
1. Upper cover
2. Enlargement screw
3. Oil tank
4. Hydraulic oil
5. Piston
6. Hydraulic cylinder
7. Packing ring
8. Vehicle lifting jack foot
9. Drain valve
10. Safety valve
11. Pimp piston
12. Pump body
13. Packing ring
General Safety Instructions
Prior to the initial use of the unit, the operating instructions
should be read completely. If in doubt with regard to
connection and operation of the unit, consult the manufacturer
(servicing department).
FOLLOW THE INSTRUCTIONS BELOW CAREFULLY IN
ORDER TO SECURE A HIGH DEGREE OF SAFETY:
CAUTION!
• All the accidents prevention statutory instruments and
the other general safety and occupational medicine
regulations applicable to power means must be
observed. Any other use is considered a use
inconsistent with determination. The manufacturer shall
not be held liable for any damages resulting therefrom.
Operating instructions are included in the delivery and in
case of resale, they should be forwarded to a new
owner.
• The work powers and competences have to be
determined clearly and observed so that no uncertain
competences arise in respect of the safety.
• Mechanical maintenance works should be done at
specified intervals and within the specified scope
• Following the maintenance, any removed protection
devices must be put at places with an expert diligence.
The protection devices and their effect must be checked
by an expert before the unit is put in operation again.
• Any faults and defects have to be reported immediately
after being recognised. The vehicle lifting jacks have to
be marked as appropriate to minimise the scope of
damage and not to affect the safety of the unit. The
warranty claims becomes nil and void if the stipulation is
not observed.
• There are places and parts on the unit that cannot be
hidden or protected. However, the function and
serviceability of the unit is not affected. Good personal
safety practices of the operator are therefore essential
for protection of the operating person and the protection
from damage of the unit.
• The vehicle lifting jacks may thus be used and operated
only within the conditions stipulated in the contract of
delivery and service.
• In principle, any additional equipment, alterations, or
conversion of the units are prohibited. They are always
subject to an agreement with the manufacturer.
• If (residual) hazards and risks arise in operation not
described in this operating manual, the operator shall
be obliged to report them to the manufacturer.
• Never excess the lifting capacity defined for the jack.
• Use the vehicle lifting jack on a strong and flat base
only.
• Never work under the lifted vehicle unless more
safety measures have been taken to prevent travel,
slide or tilting of the vehicle.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude 2T 18016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude 2T 18016 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info