Manual Gude 1800-12 V 55128 (page 11 of 44) (English, German, Dutch, French, Italian)

628789

Zoom out

Zoom in

1/44

• SPARE PARTS AND ACCESSORY EQUIPMENT

Original spare parts may only be used for servicing. The

warranty will not apply when other parts are used. Parts

and accessory parts considered to be used with this

appliance may only be used. The respective parts can

be obtained from Güde GmbH & Co. KG.

Special instructions for using this

electric winch

The use of this power appliance may lead to special

dangerous situations. The use requires a special caution to

provide safety of the operator and other persons.

Cable:

Check whether the cable is in a good condition and whether

fixed properly. Do not use the winch if the cable is worn

through. Do not change the cable for a cable that is less firm.

Battery:

Check whether the battery is in a good condition. Avoid any

contact with the accumulator acid or any other harmful

substances. Use appropriate eye protection equipment for

works on the battery. Let the engine run when using the

winch to prevent the battery from discharging.

Keep distance:

Do not stand in the cable pull direction. If the cable slips off or

pulls apart, it gets shot in that direction. If the winch is being

operated, avoid any contact with hands, clothing, hair or

jewels near the winch. Invite another person who will check

whether the winch can be used safely. Before starting the

winch, make sure such person keeps sufficient distance from

the vehicle and the cable.

Performance limits:

Do not try to exceed the limit values for the pulling force of

this winch.

Never use the hand crank to “support” the winch. This would

damage the winch and could cause injuries.

Secure the pulled load before releasing the cable on the

winch.

Installation (pic. E)

Connection of electric winch cables

The winch cables can be connected temporarily or

permanently:

1. Lift the rubber gasket and put the cable outlet to the plug

on the right of the winch body. Put the cable from the

winch to the battery and make sure it does not get to the

rotating parts and the risk of tripping is prevented.

2. Connect the black terminal on the cable to the vehicle

frame to form ground connection. Connect the red

terminal to the positive pole (+ / red) of the battery.

Notice: Make sure the battery used is a 12 V car battery

or a similar battery in a good condition.

Caution: the appliance cannot be connected to a

vehicle lighter.

3. Lift the rubber gasket on the left of the winch body.

Grasp the remote control and put the outlet on the cable

end to the plug on the left of the winch body.

4. Put the remote control on a safe place until the winch is

ready to be operated.

CAUTION!

1. Red and red (positive and positive) and black with frame

to be connected at all times – as ground connection if

the battery of the vehicle is used as a source of current.

2. Never use the winch or any other accessory equipment

until

the battery gets discharged to the full extent.

3. If the engine is running when the winch is being

operated to make the battery charged, maximum

caution is necessary for works on the vehicle and

around the vehicle.

4. Any dirty, corroded or leaking battery must not be used

as the leaking acid could cause a risk of injury.

5. For all works on the battery or with the battery,

protective glasses meeting applicable requirements for

works of that type must be worn.

Winch installation (pic. B, C, D)

The winch has been dimensioned in a way it can be

temporarily installed using foxing equipment for

attachment.

1. Hook the adapter plate to the winch basic plate using

the three pin screws.

2. The assembly comprising the winch and adapter plate

can be fastened to the attachment by putting the

spherical head through the given opening in the adapter

plate.

Using the winch (pic. F, G, H, I)

1. Put the vehicle transmission to an idle position (never

use the winch when a gear is engaged or the park

braking system applied as the vehicle transmission

could get damaged). Apply the hand brake. Support the

wheels by suitable wedges to prevent the vehicle from

moving.

2. To lift the cable, press the respective switch on the

remote control and put it out of the coil with slight

tension. Leave at least three cable windings on the coil

at all times to prevent the cable from pulled out of the

coil. Alternatively, the rope may also be pulled out using

the coil idle function. For that purpose, turn the coupling

knob (pic. 1/10) clockwise and release it. Pull the rope

out to the required length. Keep at least three windings

on the coil.

3. Hook the cable using the hauling rope, chain or hook it

in any other suitable manner to the pulled object. Never

put the cable around any object and then hook directly

to the rope as the pulled item would get damaged by

this and the cable could pull apart or fray.

4. Retighten the coupling knob.

5. Move back to a safe place from where operate the

remote control switch in a way to draw the cable and

pull the item using the winch in the required manner.

6. When lowering the load, press the respective remote

control switch and release slowly.

CAUTION!

1. If the winch is being operated, avoid any contact with

hands, clothing, hair or jewels near the drum and cable.

2. Never use the winch if the cable is frayed, broken or

damaged.

3. Never let anyone standing near the cable or at the winch

in line with the cable if pulling force is being applied on

the cable. If the cable slips off or gets broken, it may

suddenly shoot backward and put all bystanders at risk.

If the winch is being operated, all persons must be in

sufficient side distance from the winch.

Operation with the idle pulley (pic. K, L, M)

Pulling force

1. The winch has a pulling force of 1800 kg without the idle

pulley and 3600 kg with the idle pulley. As a result, the

winch may be practically used for the following:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude 1800-12 V 55128 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude 1800-12 V 55128 Manual

Product: