Manual Gude 01977 DHH 1100-13 TEZ (page 14 of 56) (English, German, Dutch, French, Italian)

624548

Zoom out

Zoom in

1/56

Assembly and first starting up

CAUTION!

BOTH DRIVES SHOULD IN NO CASE BE USED AT THE

SAME TIME! #01977

ENSURE PROPER CONNECTION OF THE PRESSURE

PIPING TO PROVIDE VALVE WORKING.

MAKE SURE THERE ARE NO UNAUTHORISED PERSONS

IN THE DANGEROUS AREA!

Residual risks and protective measures

The appliance has been designed according to the state of

the art and recognised safety technical regulations.

Despite that, there might be some residual risks when

working.

 Risk of injury to fingers and hands caused by the splitter

when wood is guided or put in an unauthorised manner.

 Injuries by a thrown-off piece of wood caused by

unauthorised holding or guiding.

 Risk to health by splinters and cuttings. Personal

protective equipment such as protective gloves should

necessarily be worn.

 Risk related to current when improper feeder cables are

used.

 Hidden residual risks may be generated despite all taken

preventive measures.

 However, residual risks may be minimised if safety

instructions, use as designated principles and Operating

Instructions are followed.

Driving engine #01977:

The fitted electric motor is connected in a way that it is ready

to be operated.

Connection corresponds to appropriate VDE and DIN

provisions.

Connection to network on the customer side and the

extension cable used must match the relevant regulations.

CAUTION!

RISK OF GETTING JAMMED! PAY ATTENTION TO YOUR

HANDS WHEN USING THE SPLITTING TABLE. THE

BOTTOM HEIGHT STOP MUST BE ADJUSTED SO AS TO

GUARANTEE SAFE DISTANCE OF 6-8 CM BETWEEN THE

SPLITTING KNIFE AND SPLITTING TABLE.

See the pictures

Operating staff

(pic. 3, 4, 5, 6, 12 and 13)

Putting the appliance into operation when the cylinder is

started:

 To start the end switching at the electrically driven splitter,

pulling the operator lever or lifting the end break arc – at

the eyes height – is enough.

 If you start the engine or the output shaft now, release

blocking and pull both operating levers. Now the piston

rod is pressed out of the cylinder and consequently, the

cylinder goes slowly up (pic. 3). CAUTION: Pay

necessary attention to hydraulic hoses!!!

 Insert carefully and slowly the screws in the hole, grab the

switching handle and screw the nuts on the screws (pic.

4).

Never guide the cylinder quickly up and do not use force!

 Any mistakes in operation are naturally excluded from the

guarantee!!

 Now release the switching handle; the splitting wedge is

guided upwards from the piston rod. The wood splitter is

now ready to be operated (pic. 5).

Putting the appliance into operation when the cylinder is

lifted:

 Connect to network, switch on the engine, finished (pay

attention to the speed direction!)

 Connect the output shaft, finished.

Starting the appliance for transport reasons:

Put a wooden block with a height of app. 15 – 20 cm on the

floor board. Pull the switching handles and drop the splitting

wedge down to the wooden block. Now grab the switching

handle and block the backward movement. Now switch off the

engine or the output shaft.

 (Block the limit switch if you are alone)

 Screw both nuts off the fitted pin to release the cylinder

board from the frame (pic. 3).

 Now switch on the engine or the output shaft again.

 The cylinder now drops down to the splitting wedge if the

switching handle is not pulled.

 When it has dropped down, pull the switching handle and

switch the appliance off.

Switch the engine on and pay attention to the turning direction.

If the switch is not responding when operating levers are

pulled, the polarity must immediately be changed (see the

Plugging in / Hydraulic device)

Two-handed operation

Wear proper working gloves when splitting wood!

 Wood is held by the holding mechanism.

 The splitting process is initiated by movement of both

switching handles down.

 The splitting knife movement is stopped by releasing one

switching handle.

 The splitting knife returns to the upper position when both

switching handles are released.

Stroke limitation

Upper position of the splitting knife 3...5 cm above the

split wood

 Guide the splitting knife to the required position

 Release the operating lever or switch the engine off

 Release the locking bush A and press the arc (pic. 6)

 Release both operating levers or switch the engine on

 Check the upper position of the splitting knife

Downward stroke limitation

Long pieces of wood

 Cylinder goes out just maximum 104 cm (pic. 12).

 Adjustment bush in the highest position (pic. 13).

Splitting pace:

There are two splitting paces: the engine is moving quickly in

the split wood direction by slight pulling the operating levers.

The knife forward movement is reduced to the splitting pace

with maximum performance being achieved by full pressing

down.

CAUTION: Never split with the fast forward movement! Press

the operating levers down to the stop when splitting.

Blocks/splitting table

Optionally available:

Matching short wooden table for hanging.

Güde Article No: # 02017

 Put the splitting knife down to 5 cm above the block table.

 Release the operating lever and switch the splitter off.

 Perform corresponding adjustment (pic. 13).

Split wood length

The hydraulic wood splitter is suitable for splitting blocks (fitted

splitting table) and one-metre woods. The maximum stroke

can be limited (see the Stroke limitation).

The effective upward stroke limitation is app. 3 – 5 cm above

the wood.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude 01977 DHH 1100-13 TEZ in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 5,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude 01977 DHH 1100-13 TEZ Manual

Product: