629293
25
Zoom out
Zoom in
Previous page
1/48
Next page
Installation & Programming Guide — 25
System programming options are split into three categories :-
1. Basic Standard control panel functions
2. Advanced Enhanced programming functions
3. Communicators/Tx Communicator options to allow Tx channel assignment and
communication customisation.
Code Function Options
500 Full Set Entry 0 - 99 seconds
(Default 30)
501 Part Set Exit 0 - 99 seconds
(Default 15)
502 Full Set Exit 0 - 99 seconds
(Default 20)
503 Bell Duration 0 - 30 minutes
(Default 15)
510 Set Indication 0 - log on only : 1 - always
511 Output 1 6 options
(Detector reset default)
512 Output 2 6 options
(Detector latch default)
513 Time/Date Change
514 Strobe 0 - until unset: 1 - as bell
515 User Authority Levels 5 authorities for users 02 - 14
516 Final Setting 0 - exit time expiry : 1 - exit point closure
517 PIN Attempts 0 - 99
(Default 0 - wrap around PIN)
*when PIN attempts is programmed, the user
must press confirm after the entry of
their PIN code.
518 Remote Fault Bypass 0 - off : 1 - on
520
Remote/Push Button Set
0 - remote set : 1 - push button set
523
Technistore Reset Version
0 - 255
(Default 0)
524 PA Rearm 0 - Rst : 1 - Bell
525 Auto Re-arm 0 - 9 auto rearm attempts
526 Alarm Reset 0 - customer reset : 1 - engineer reset
527 PA Reset 0 - customer reset : 1 - engineer reset
528 Technistore Reset 0 - off : 1 - on
529 Speaker Duration 0 - as bell : 1 - until unset
530 Audible Exit Fail 0 - off : 1 - on
531 Day Tamper Sounders 0 : Internal only 1 : External & Internal
532 Part Set Sounders 0 : Internal only 1 : External & Internal
533 Entry Alarm 0 - active : 1 - disabled
534 Entry Route Warning 0 - non warning : 1 - with warning
521 Part Set Tx Enable 0 - disable Tx : 1 - Enable Tx
550 Bell Delay 0 - 30 minutes
(Default 0)
551 Tx Reset 0 - reset : 1 - Bell : 2 - Logon
552 Day Tamper Comms 0 - no Comms : 1 - Comms
553 Set Line Fault 0 - cannot set with line fault
1 - set with line fault
554 Line Fault 0 - silent line fault : 1 - audible line fault
555 Line Fault Delay 0 - 60 seconds
(Default 0 - instant)
560 Tx Signalling Tx type assignment
562 Verification Period 0 - 255 (minutes)
563 Verify Zone Tx 0 - off : 1 - on
Programming CodesProgramming Codes
Programming CodesProgramming Codes
Programming Codes
Installation & Programming
COMMS/TX
ADVANCED
BASIC
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guardall WINDSOR SERIES 300i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guardall WINDSOR SERIES 300i in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info