580330
42
Zoom out
Zoom in
Previous page
1/46
Next page
PX Version 5.0 - QX/RX Version 4.51 Installation Manual – Issue F
- 42 -
Introduction
The Dual Comm module, GSM module and the PSTN module may be used with any Guardall control
panel.
Feature Implementation
Transmission Voice and Data
Frequency Band Dual Band EGSM900 and EGSM1800
Transmit Power Class 4 (2W) for EGSM 900MHz
Class 1 (1W) for EGSM 1800MHz
Data 9.6Kbps
Supported SIM card 3V cards
There are a number of important points to consider when using one of the new module types with an
existing panel:
1. All previous communicators were designed for use within the panel case and consequently they
were designed with no tamper switch. The GSM/Dual comm module is intended for use outside
the panel case, and so needs a case tamper. The GSM/Dual comm module case tamper is
recognised from panel v4. If the GSM/Dual comm module used with earlier panel versions it is
recommended that line fault monitoring is enabled to act as a substitute for the tamper sensing.
2. The Dual comm module functions are programmed using the DIL switches. Future versions of the
firmware will include additional menu options for GSM programmable functions.
The latest firmware release is V4.52c. This is necessary to enable older panel versions to recognise
the module and allow access to the appropriate programming menus.
Installation
Special care is required when installing the GSM module or Dual Comm module;
1. Avoid placement on metal surfaces to ensure good radio performance.
2. To minimise GSM transmission interference, route all cables away from the GSM antenna.
3. If the system includes Audio Modules ensure that there is at least 3m between the Audio
Module(s) and the GSM/Dual Comm module.
4. The maximum recommended XiB bus cable length between the power supply and the GSM/Dual
Comm module is approximately 80m. This distance may be doubled if two cable cores are used
for the power connections. This restriction is based on the peak current requirement of 180mA
under poor signal conditions.
5. Insert a valid SIM card into the slot provided in the GSM engine. SIM code password protection
must be disabled.
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guardall PX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guardall PX in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Guardall PX

Guardall PX User Manual - English - 46 pages

Guardall PX Installation Guide - English - 46 pages

Guardall PX User Manual - English - 52 pages

Guardall PX Additional guide - Dutch - 42 pages

Guardall PX Additional guide - Dutch - 48 pages

Guardall PX Additional guide - Dutch - 52 pages

Guardall PX User Manual - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info