580330
14
Zoom out
Zoom in
Previous page
1/52
Next page
PX Control Panel User Manual – Issue C
- 14 -
Message Reason
Alarm Abort User logs on within the alarm abort period (programmable option)
Setting Stopped User logs on during the setting exit period
Group Unset A group(s) is set and is programmed to automatically unset when a user logs on.
Cannot Set The system cannot set, the reason(s) will then be displayed.
Unset Alarm An unset alarm has occurred, the details will then be displayed.
Mult.Alarm A circuit(s) has alarmed the maximum number of times allowed (programmable).
The circuit details will then be displayed.
Code Known
Another user has chosen your code. You will then be given the option of
immediately changing your code. This message will always be displayed on log
on until the code is changed.
Call Engineer You should call the installation company. The details will then be displayed.
Reset OK A managed reset code has been accepted
Set
4=Confirm
The user is configured for the log on set option. If confirmed the system will start
setting (if only one group is authorised) or display the set group menu.
Soak Cct Fails Circuits which have been put on special test by the installation engineer have
alarmed.
Dual User Code Operation
Where a higher level of security is required a keypad may have been programmed to require two user
codes to be entered before logging a user on to the system. Both user codes must be authorised and
are logged by the system. The authority of the second user code entered is used by the system.
Unset
Code-01
The system will have been partitioned by the installation engineer into a number of set groups. The user
authority will determine the choice of groups, which can be unset. There are several methods of
unsetting available to the user. These methods are discussed in the following section.
Unsetting Methods
If a set group incorporates an entry route in the unsetting procedure then opening a final entry door to
the area will start a pre-programmed entry timer. The user must proceed directly to the keypad or
keyswitch via a pre-determined entry route and unset the group as described.
If the group is not unset before the entry time has expired a warning period, equivalent to 50% of the
programmed entry time, will be allowed. This is to warn the user that an alarm condition will occur if the
group is not unset by the end of the warning period. If the group is not unset by the time that the total
entry time and warning time has expired, an alarm condition will be initiated.
During the entry time, if a user deviates from the prescribed entry route into an armed area, the entry
time is immediately cancelled. If programmed, a fixed pre-warning period of 45 seconds will be given,
otherwise an immediate alarm will be given. If the user enters an armed area during the entry warning
period, the warning period is cancelled and an immediate alarm will be given.
Unsetting from a keypad
To unset, log on to the keypad. If an authorised group is configured for automatic logon/unset then the
unset group descriptor will be displayed.
Workshop
Unset
If more than 1 group is configured for logon/unset then only the first
descriptor will be displayed.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Guardall PX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Guardall PX in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Guardall PX

Guardall PX Installation Guide - English - 46 pages

Guardall PX User Manual - English - 46 pages

Guardall PX Installation Guide - English - 46 pages

Guardall PX Additional guide - Dutch - 42 pages

Guardall PX Additional guide - Dutch - 48 pages

Guardall PX Additional guide - Dutch - 52 pages

Guardall PX User Manual - Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info