634623
13
Zoom out
Zoom in
Previous page
1/15
Next page
13
OPERATION _______________________________
Wall mount installation
Notes
Install the wall mount
Q
near an appropriate
power outlet, this allows you to charge the unit
hassle-free.
Make sure that the nearest power outlet is
reachable by the power adapter
P
.
Leave sufficient free space above the wall mount
so you can easily place the vacuum cleaner on
the mount.
Install the wall mount out of the reach of
children.
1 Install the wall mount
Q
at the desired wall
position.
2 Mark boreholes for the three screws.
Caution
Make sure that you do not drill over wiring,
cables or water pipes!
3 Drill the boreholes and insert dowels.
4 Secure the wall mount
Q
with three screws.
Make sure that the screws can carry the weight
of the vacuum cleaner and its accessories.
Charging the battery
1 Insert the adapter cable
P
in the port
K
in the
rear part of the motor unit
J
.
2 Connect the power adapter
P
to an
appropriate power outlet.
– The charge indicator
L
lights up blue and will
be off after the battery is fully charged.
– The vacuum cleaner must be turned off while
charging.
– The vacuum cleaner is fully charged after
approx 14 hours and the operating time is 7
to 10 minutes.
Notes
Only recharge the battery when it is nearly
empty. This increases the battery’s lifespan.
Charge the battery at a room temperature
between 0°C and 37°C.
To increase the battery’s lifespan, charge the
battery completely before the first use for approx
16 hours and discharge it again completely.
The maximum charging time is 24 hours and
may not be exceeded.
Dry vacuum cleaning
1 Insert the filter nozzle
F
into the container
G
and the HEPA filter
H
into the filter nozzle
F
.
2 Place the container
G
on the motor
unit
J
so
that the lock
E
clicks in audibly.
3 If necessary, connect the crevice nozzle
M
or
brush nozzle
O
to the container
G
.
4 To turn on, switch the On/Off switch
A
in
position I.
5 To turn off, switch the On/Off switch
A
in
position 0.
Wet vacuum cleaning
1 Insert the filter nozzle
F
into the container
G
.
2 Place the container
G
on the motor
unit
J
so
that the lock
E
clicks in audibly.
3 Connect the wet nozzle
N
to the container
G
.
4 To turn on, switch the On/Off switch
A
in
position I.
5 To turn off, switch the On/Off switch
A
in
position 0.
6 Empty the container
G
immediately after wet
vacuum cleaning.
Notes
If the area to be cleaned is poorly lit, push the
light button
C
to turn on the light
D
.
Use the
same button to turn off the light.
The capacity of the container
G
is 0.5L for dry
vacuum cleaning and 0.15L for wet vacuum
cleaning. Observe the MAX marker for liquids
on the container
G
.
The HEPA filter
H
is not used for wet vacuum
cleaning.
Do not vacuum dry and wet dust simultaneously.
Empty the container
G
between dry and wet
vacuuming.
ENGLISH
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig VCH 5040 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig VCH 5040 in the language / languages: English, German as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info