569615
5
Zoom out
Zoom in
Previous page
1/7
Next page
Radio Reception
Switch the radio on with the button
RADIO ON.
The illuminated pointer DIAL 6 serves as
'on' indicator.
Select the waveband with the FM • MW
switch:
FM = VHF
MW = Medium Wave
Tune to stations with the rotary control
TUNING.
Adjust the volume with the rotary control
VOLUME.
Switch the radio off with the button
RADIO/ALARM OFF.
Aerials
For receiving MW stations there is a ferrite
rod aerial inside the set.
Rotating the unit slightly can improve
reception.
The wire aerial at the back of the set is
used for VHF (FM) reception.
Position the wire aerial so that optimum
reception is obtained.
Auto Dimmer
The brightness of the display is automatically
adjusted to the actual room illumination by the
AUTO DIMMER sensor.
Setting the clock time
Press the TIME button and hold it pressed.
Set the clock time with the 1 and 22
buttons:
Fast forward with the 22 button.
Slow backward with the 1 button.
Release the TIME button.
Indicating the seconds
Press the SNOOZE button and hold it
pressed.
The display shows the unit digit of the minutes
and the running seconds, e.g.: at 12:15
hours, 20 seconds –> indication 5:20.
Setting the alarm time
Your Sonoclock 186 allows you to set two
alarm times (e.g., for two different persons).
Set the ALARM 1/2 switch to
alarm time 1
(
ALARM 1
) or alarm time 2
(ALARM 2).
Select the required alarm function (radio
alarm or sound signal alarm) with the switch
ALARM /ɷ/OFF.
The corresponding light dot on the display
shows which alarm time can be set:
ALARM 1 6 =
alarm time 1
ALARM 2 6 =
alarm time 2
Press the ALARM button.
The display shows the present alarm time.
Press and hold down the ALARM
button
and set the alarm time with the
1 and 22
buttons (in the same way as the clock time).
Note:
If the ALARM 1/2 switch is set to
position ALARM 1+2, it is not possible to
display or to set the alarm times.
8
Sonoclock 186 page 8
GB
POWER SUPPLY CLOCK RADIO
Connecting the unit
The unit is designed to operate from a mains supply
of 230 V, 50 Hz~.
When the set is connected for the first time or after a
power failure (without standby battery
fitted), the
display flashes to indicate that the clock
and, if
necessary, the alarm time (s) should be set.
Standby-battery – mains failure
If a standby battery is fitted, the clock will continue to
operate during mains failure. However, the display will
not be illuminated, the radio does not work and the
alarm will not sound unless the mains supply is restored
within 59 minutes of the preset alarm time (if so, the
radio will switch on or the alarm tone will sound).
Insert a 9 V alkaline battery (IEC 6 LF 22) into the
battery compartment on the bottom of the unit.
Insert the battery only after the unit has been connected
to the mains in order to prevent unnecessary drain.
We recommend that the battery is replaced after
approx. 1 year.
If the clock radio is to be disconnected for a long
period, the standby battery should be removed, as it
would otherwise discharge too quickly and may leak.
Note on Environmental Protection
Do not throw exhausted batteries in the
household refuse.
Hand over the old batteries to your dealer or
public collecting points when buying new ones.
Note:
The unit remains connected to the mains
even when it is switched off.
The unit is only fully isolated from the mains if the
mains plug is removed from the wall socket.
Important note for users in the U.K.:
When fitting a mains plug, follow the instructions
on page 2.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig SONOCLOCK SC 186 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig SONOCLOCK SC 186 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Grundig SONOCLOCK SC 186

Grundig SONOCLOCK SC 186 User Manual - German - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info