544906
85
Zoom out
Zoom in
Previous page
1/92
Next page
85 / 92 EN
Washing Machine / User‘s Manual
8 Troubleshooting
Programme cannot be started or selected.
Washing machine has switched to self protection mode due to a supply problem (line voltage, water
pressure, etc.). >>> Press and hold Start / Pause button for 3 seconds to reset the machine to factory
settings. (See "Cancelling the programme")
Water in the machine.
Some water might have remained in the product due to the quality control processes in the production.
>>> This is not a failure; water is not harmful to the machine.
There is water leaking from the bottom of the machine.
Likely problems with hoses or the pump filter. >>> Be sure the seals of the water inlet hoses are securely
fitted. Attach the hose to the tap tightly.
Pump filter might not be closed fully. >>> Check if the pump filter is completely closed.
Machine does not fill with water.
Tap is turned off. >>> Open the taps.
Water inlet hose is bent. >>> Correct the hose.
Water inlet filter is clogged. >>> Clean the filter.
The loading door is ajar. >>> Close the loading door.
Machine does not drain water.
Water drain hose might be clogged or twisted. >>> Clean or flatten the hose.
Pump filter is clogged. >>> Clean the pump filter.
Machine vibrates or makes noise.
Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
A hard substance might have entered into the pump filter. >>> Clean the pump filter.
Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or
distribute the load by hand to balance it homogenously in the machine.
Machine might be leaning on a rigid item. >>> Check if the machine is not leaning on anything.
Machine stopped shortly after the programme started.
Machine might have stopped temporarily due to low voltage. >>> It will resume running when the
voltage restores to the normal level.
Machine directly discharges the water it takes in.
Draining hose might not be at adequate height. >>> Connect the water draining hose as described in the
operation manual.
No water can be seen in the machine during washing.
The water level is not visible from outside of the washing machine. This is not a failure.
Loading door cannot be opened.
Door lock is activated because of the water level in the machine. >>> Drain the water by running the
Pump or Spin programme.
Machine is heating up the water or it is at the spinning cycle. >>> Wait until the programme completes.
Child lock is engaged. Door lock will be deactivated a couple of minutes after the programme has come
to an end. >>> Wait for a couple of minutes for deactivation of the door lock.
85


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig GWN 47230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig GWN 47230 in the language / languages: German as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info