769852
12
Zoom out
Zoom in
Previous page
1/56
Next page
12 / EN Washer-Dryer / User Manual
3.3 Removing the transit bolts
A
PRECAUTION!
Do not remove the transit bolts before
removing the packaging reinforcement.
Remove the transit bolts before operating
the washing machine! Otherwise,
the product will get damaged.
3
2
1
1 Use a tool to loosen all bolts
until they rotate freely.
2 Remove the transit bolts by
turning them slightly.
3 Attach the plastic covers supplied in the user
manual bag into the holes on the rear panel.
C
INFORMATION
Keep the transit bolts in a safe place
to reuse when the product needs
to be moved again in the future.
Never move the product without the
transit bolts properly fixed in place!
3.4 Connecting water supply
C
INFORMATION
The water supply pressure required to
run the product is between 1 to 10 bars
(0.1 – 1 MPa). It is necessary to have
10 – 80 liters of water flowing from the
fully open tap in one minute to have your
product run smoothly. Attach a pressure
reducing valve if water pressure is higher.
A
CAUTION!
Models with a single water inlet should
not be connected to the hot water
tap. In such a case the laundry will get
damaged or the product will switch to
protection mode and will not operate.
Do not use old or used water inlet
hoses on the new product. It may
cause stains on your laundry.
1 2 3
1 Connect the special hose supplied with the
product to the water inlet on the product.
A
CAUTION!
Ensure that the cold water connection
is made correctly when installing the
product. Otherwise, your laundry
will come out hot at the end of the
washing process and wear out.
2 Tighten the hose nuts securely by hand.
Never use a tool when tightening the nuts.
3 Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leak occurs, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. In order
to prevent the water leaks, keep the taps
closed when you do not use the product.
3.5 Connecting to the drain
Attach the end of the drain hose directly
to waste water drain, sink or bathtub.
A
CAUTION!
Your house will be flooded if the hose
comes out of its housing during water
discharge. Moreover, there is risk of
scalding due to high washing temperatures!
To prevent such situations and to ensure
smooth water intake and discharge of
the machine, fix the end of the discharge
hose tightly so that it cannot displace.
90 cm
90
40
90
40
90 cm
90 cm
min.40
Connect the hose to a minimum height of
40 cm and a maximum height of 90 cm.
If the hose is run along the floor (or at less
than 40 cm above it) and raised later on,
water drain becomes difficult and laundry
may come out extremely wet. Therefore,
observe the heights described in the figure.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig GWDI8542 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig GWDI8542 in the language / languages: English as an attachment in your email.

The manual is 5.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info