712283
38
Zoom out
Zoom in
Previous page
1/160
Next page
36
ENGLISH
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision. (XE requirement - English only)
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Lock-Off Button and Variable Speed Trigger
(Fig. A)
DCS334
To lock the variable speed trigger
1
, press the lock-off
button
2
. When the lock-off button is depressed to the lock
icon, the unit islocked.
Always lock the trigger switch when carrying or storing the tool
to eliminate unintentionalstarting.
To unlock the trigger switch, press the lock-off button. When
the lock-off button is depressed to the unlock icon, the unit
isunlocked.
NOTE: The lock-off button is colored red to indicate when the
switch is in its unlockedposition.
To start the DCS334 jig saw, squeeze the variable speed
trigger
1
.
To slow and stop the jig saw, release thetrigger.
As the trigger is pressed in, the strokes-per-minute continue
to increase, but up to the maximum speed of the tool. As the
trigger is released, the blade strokes-per-minutereduce.
NOTE: This tool has no provision to lock the switch in the ON
position, and should never be locked ON by any othermeans.
On/Off Switch (Fig. A)
DCS335
CAUTION: Move the on/off switch
1
to the OFF position
before inserting the batterypack.
To start the DCS335 jig saw, move the on/off switch
1
to the
ON position. To turn the jig saw off, move the on/off switch to
the OFFposition.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, depress the trigger lock button and
disconnect battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can causeinjury.
WARNING: Use only
DeWALT
battery packs andchargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
DCS335: Move the on/off switch
1
to the OFF position before
inserting the batterypack.
NOTE: Make sure your battery pack
11
is fullycharged.
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack
11
with the rails inside the
tool’shandle.
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap intoplace.
To Remove the Battery Pack from the Tool
DCS335: Move the on/off switch
1
to the OFF position before
removing the batterypack.
1. Press the release button
12
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig. C)
Some
DeWALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
Blade Installation and Removal (Fig. D, J)
To Install a Blade
NOTE: This jig saw uses only T-shank jig sawblades.
NOTE: The DT2074 flush cutting blade is for use with D
e
WALT
DCS334 and DCS335 jig sawsonly.
NOTE: When installing flush cutting blades (DT2074), the anti-
splinter insert (
20
, Fig. J) must be removed and the shoe must
to be in the 0° positive stopposition.
NOTE: The correct saw blade must be selected for the material
beingcut.
1. Hold open the blade release latch
4
as shown in FigureD.
2. Insert the T-shank blade into the clamp mechanism
13
while guiding the back of the blade into the groove of the
guide rollers
14
.
3. The T-shank should be completely inside the
clampmechanism.
4. Release the blade releaselatch.
To Remove a Blade
CAUTION: Do not touch used blades, they may be hot.
Personal injury mayresult.
1. Hold open the blade release latch
4
.
2. With a slight shake the blade will dropout.
3. Release the blade releaselatch.
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig GTN 27250MG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig GTN 27250MG in the language / languages: German as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info