773800
10
Zoom out
Zoom in
Previous page
1/44
Next page
DISHWASHER / USER INSTRUCTIONS 9 / 43 EN
3INSTALLATION
To make the product ready for use, make
sure that the electricity, tap water supply and
water drainage systems are appropriate
before calling the Authorised Service Agent.
If they are not, call a qualified technician
and plumber to have any necessary
arrangements carried out.
CPreparation of the location and
electrical, tap water and waste
water installations at the place
of installation is under customer's
responsibility.
BManufacturer shall not be held
responsible for damages arising
from processes carried out by
unauthorised persons.
APrior to installation, visually
check if the product has any
defects on it. If so, do not have
it installed. Damaged products
cause risks for your safety.
CMake sure that the water inlet
and discharge hoses are not
folded, pinched or crushed
while pushing the product into
its place after installation or
cleaning procedures.
When placing the product, pay attention not
to damage the floor, walls, piping, etc. Do
not hold the product from its door or panel
to move it.
Appropriate installation
location
Place the product on a solid and flat
floor that has sufficient load carrying
capacity! The product must be installed
on a flat surface in order for the door to
be closed comfortably and securely.
Do not install the product at places
where temperature may fall below 0ºC.
Place the product on a rigid floor. Do
not place it on a long pile rug or similar
surfaces.
BEnsure the power cable does not
get trapped under the product.
Make sure that you select a location
that will allow you to load and unload
the dishes in a fast and comfortable
manner.
Install the product in a place close
to the tap and the drain. Select the
installation location by considering
that it will not be changed after the
connections are made.
Connecting water supply
Do not use old or used water inlet hose
on the new product. Use the new water
inlet hose supplied with the product.
Connect the water inlet hose directly
to the cold water tap. Permitted water
temperature up to 25°C. Pressure
coming from the tap should be minimum
0.3 and maximum 10 bars. If the water
pressure exceeds 10 bars, a pressure
relief valve should be installed in
between.
Open the tap completely after making
the connections to check for water
leaks.
AFor your safety, close the water
inlet tap completely after the
washing programme is over.
Connection to the drain
Water discharge hose can directly be
connected to the drain hole or sink’s
drainage. The length of this connection
must be min. 50 cm and max. 100 cm from
the floor. A discharge hose longer than 4
meters will cause washing performance to
be affected.Attach the water discharge hose
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig GNV22620 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig GNV22620 in the language / languages: English as an attachment in your email.

The manual is 11.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info