569683
76
Zoom out
Zoom in
Previous page
1/88
Next page
ENGLISH
76
»KB Frequency (MHz)«: Enter the user
band frequency assigned to the user
band with »1...0« buttons.
»LNB Selection«: If more than one
satellites are used in the current SCR
system, select »1/2« to»2/2« for the
satellite corresponding to the relevant
positions using »
<
« or »
>
« buttons.
Notes:
7
Use installation equipment supported /
suggested by your Multiswitch.
7
Other users / receivers connected to the
system may be affected if the specified user
band number and frequency is changed
during installation.
7
User band and User band frequency is
specified on the Multiswitch used; and
each user / receiver uses a specified user
band and user band frequency.
7
With SCR satellite system, auto search by
several users / receivers at the same time
may cause problems.
»22 KHz«: Depending on the LNB type,
22 kHz audio is selected. For a univer-
sal LNB, this option is set to »Auto« and
cannot be changed.
»DISEqC mode« and »LNB selection«:
depending on the type of antenna used,
use »
<
« or »
>
« select the option »Off«,
»DiSEqC 1.0« or »DiSEqC 1.1«.
»Off«: for a satellite system with only
one antenna.
» DiSEqC 1.0«: allows up to four satel-
lites to be received simultaneously.
Under »LNB selection«, use »
<
« or
»
>
« to select the option »1/4«, »2/4«,
»3/4« or »4/4«.
» DiSEqC 1.1«: allows up to 16 satel-
lites to be received simultaneously.
Under »LNB selection«, use »
<
« or
»
>
« to select the option »1/16« to
»16/16«.
5 Press »MENU« to end the setting.
SPECIAL SETTINGS
----------------------------------------------------------------------------------------------------------
Settings for motorised antennas
(DiSEqC 1.2)
Your television set supports motorised satellite
systems in compliance with DiSEqC 1.2. This
function allows the satellite antenna to be oper-
ated via the television set.
1 Open the menu with »MENU«.
2 Select the menu item »SOURCE SETUP« with
»
V
« or »
Λ
« and press
»OK«
to confirm.
The »SOURCE SETUP« menu appears.
3 Select the line »Antenna Settings« with »
V
«
or »
Λ
« and press
»OK«
to confirm.
4 Select the line »DiSEqC Mode« with »
V
« or
»
Λ
«. Select the option »DiSEqC1.2« with
»
<
« or »
>
«
The line »DiSEqC 1.2 SETTINGS« is active.
Notes:
7
Additional operations are explained in the
following sections.
7
The following description about the DiSEqC
1.2 settings premise a substantial expertise
about the satellite systems. Ask your
specialist dealer.
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig 47 VLE 9474 WL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig 47 VLE 9474 WL in the language / languages: English as an attachment in your email.

The manual is 4,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Grundig 47 VLE 9474 WL

Grundig 47 VLE 9474 WL User Manual - German - 90 pages

Grundig 47 VLE 9474 WL User Manual - Dutch - 90 pages

Grundig 47 VLE 9474 WL User Manual - French - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info