544970
47
Zoom out
Zoom in
Previous page
1/58
Next page
47
ENGLISH
SPECIAL SETTINGS
----------------------------------------------------------------------------------------------------------
»KB Frequency (MHz)«: Enter the user
band frequency assigned to the user
band with »1...0« buttons.
»LNB Selection«: If more than one
satellites are used in the current SCR
system, select »1/2« to»2/2« for the
satellite corresponding to the relevant
positions using »
B
« or »
A
« buttons.
Notes:
7
Use installation equipment supported /
suggested by your Multiswitch.
7
Other users / receivers connected to the
system may be affected if the specified user
band number and frequency is changed
during installation.
7
User band and User band frequency is
specified on the Multiswitch used; and
each user / receiver uses a specified user
band and user band frequency.
7
With SCR satellite system, auto search by
several users / receivers at the same time
may cause problems.
»DISEqC mode« and »LNB selection«:
depending on the type of antenna used,
use
»
B
« or »
A
« select the option »Off«,
»DiSEqC 1.0« or »DiSEqC 1.1«.
»Off«: for a satellite system with only
one antenna.
» DiSEqC 1.0«: allows up to four satel-
lites to be received simultaneously.
Under »LNB selection«, use
»
B
«
or
»
A
« to select the option »1/4«,
»2/4«, »3/4« or »4/4«.
» DiSEqC 1.1«: allows up to 16 satel-
lites to be received simultaneously.
Under »LNB selection«, use
»
B
« or
»
A
« to select the option »1/1 to
»16/16«.
5 Press »
M« to end the setting.
Settings for motorised antennas
(DiSEqC 1.2)
Your television set supports motorised satellite
systems in compliance with DiSEqC 1.2. This
function allows the satellite antenna to be oper-
ated via the television set.
1 Open the menu with »M«.
2 Select the line »SOURCE SETUP« with
»
C
«
or
»
D
« and press »OK« to confirm.
The »SOURCE SETUP« menu appears.
3 Select the line »DiSEqC 1.2« with
»
C
« or
»
D
«. Select the option »On« with »
B
« or
»
A
«
The line »User Mode« is active.
Note:
7
Additional operations are explained in the
following sections.
User mode
You can adjust the alignment of the satellite an-
tenna to each individual satellite. These settings
will be saved so that the antenna can later be
easily guided to each saved alignment.
1 Select the line »User mode« with
»
C
« or
»
D
« and press »OK« to confirm.
The »USER MODE« menu appears.
2 Select the preferred option with
»
C
« or
»
D
«.
»Satellite«: »Press OK«, select a satellite
with
»
B
«, »
A
«, »
C
« or »
D
« and press
»OK« to confirm.
»Transponder«: »Press «, select the tran-
sponder from which the signal is being
received with
»
B
«, »
A
«, »
C
« or »
D
«
and press »OK« to confirm.
»Moving Mode«: Use
»
B
« or »
A
« to se-
lect the option »Discrete« or »Continuous«.
»Discrete«: Moves the antenna in
defined steps to the west and the east.
»Continuous«: Moves the antenna to the
west or east continuously.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig 22 VLE 8220 BG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig 22 VLE 8220 BG in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Grundig 22 VLE 8220 BG

Grundig 22 VLE 8220 BG User Manual - German - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info