789280

Grouw 17941 - M900 Manual

71
Zoom out
Zoom in
Previous page
1/91
Next page
71
GB
3) The robot lawnmower has been lifted
The robot lawnmower will report an error if the lift
sensors are continuously activated for 10 seconds.
Press the OK button to re-start the robot lawnmower. If
the error occurs repeatedly, you should check the work
area.
Remove any obstacles of over 100 mm, as these may
cause the robot lawnmower to roll over.
Use a regular lawnmower to cut grass that is taller than
60 mm.
4) The robot lawnmower has rolled over
If the robot lawnmower rolls over, it stops automatically
and reports an error. Reposition the robot lawnmower
and press the OK button to start it again. If the error is
caused by a steep slope in the work area, change the
layout of the boundary cable to avoid the slope. Follow
the installation instructions.
5) The robot lawnmower has been overloaded
The robot lawnmower’s motor is protected against
overload. If this error occurs, it is probably because the
grass is too tall for the robot lawnmower, or the cutting
disc and the wheels are clogged with grass clippings,
mud, etc. If the grass is too tall, cut it with a regular
lawnmower and clean the robot lawnmower. Press the
OK button to re-start the robot lawnmower.
6) Low battery voltage
The battery is at. Carry the robot lawnmower to the
charging station and perform manual charging as
described below.
Manual charging
Pull the robot lawnmower out of the charging station.
Move the main switch to the OFF position and wait 5
seconds. Note that the lid must be closed.
Set the main switch to the ON position and push the
robot lawnmower into the charging station again. Do
NOT switch the robot lawnmower on using the Power
button (a)!
If the indicator light on the charging station does
not change to red at the rst attempt, pull the robot
lawnmower out of the charging station and push it back
in again. Repeat this until the indicator light turns red.
If this does not work after 10-15 times, allow the robot
lawnmower to remain in the charging station for an
hour before trying again.
When the indicator light on the charging station
lights up green, charging is complete and the robot
lawnmower is fully charged.
7) Boundary cable signal error
The robot lawnmower will rotate a number of times,
stop and report an error if it goes outside the work area
or if there is an error with the boundary cable. Check
that the robot lawnmower is within the work area and
then check the indicator light on the charging station:
Indicator light Indicates
O The charging station is not plugged
in.
Lights up
green (symbol
1)
The boundary cable is connected
correctly, the robot lawnmower
is ready and the battery is fully
charged.
Flashes green
(symbol 2+3)
There is a break in the boundary
cable.
The ends of the boundary cable are
connected the wrong way around on
the charging station.
Correct the error.
Lights up red
(symbol 4)
The battery is charging.
Flashes green
and red
alternately
Maintenance charging of battery
(trickle charging).
Note! In the event of a boundary cable signal error
If the robot lawnmower displays the Boundary Error
message, there is an error with the boundary cable
signal:
• Theboundarycableistoolong(over250m).
• Theboundarycableisassembledincorrectly,there
is moisture in a joint, or an incorrect connector has
been used.
• TheboundarycablemustNOTbestrippedwhenrst
using the connector provided.
• Youcanremovetheendsoftheboundarycablefrom
the charging station and measure the resistance
of the boundary cable using a multimeter. A new
boundary cable has a resistance of about 2 Ohm per
100 metres.
If the boundary cable’s resistance measures more
than 8-10 Ohm, the robot lawnmower will display a
boundary cable signal error.
4 3 2 1
… 71 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grouw 17941 - M900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grouw 17941 - M900 in the language / languages: English, German, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 27.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info