789277

Grouw 17940 - S600 Manual

43
Zoom out
Zoom in
Previous page
1/55
Next page
43
GB
Note!
If the error indicator light ashes red on the robot
lawnmower, there is an error in the boundary cable
signal:
• Theboundarycableistoolong(over250m).
• Theboundarycableisassembledincorrectly,there
is moisture in a joint, or an incorrect connector has
been used.
• TheboundarycablemustNOTbestrippedwhen
using the connector provided.
• Youcanremovetheendsoftheboundarycablefrom
the charging station and measure the resistance
of the boundary cable using a multimeter. A new
boundary cable has a resistance of about 2 Ohm per
100 metres.
If the boundary cable’s resistance measures more
than 8-10 Ohm, the robot lawnmower will display a
boundary cable signal error.
Correct the error or replace the boundary cable.
5) Abnormal battery temperature
The robot lawnmower will report an error if the battery
temperature during operation is outside the range of 0-
75 °C or during charging is outside the range of 0-45 °C.
The robot lawnmower returns to the charging station
and lets the battery return to a safe temperature.
The risk of this is greatest in summer, when the outside
temperature in direct sunlight approaches 35 °C. It may
be a good idea to change the start time of the robot
lawnmower so that it starts earlier in the day when it is
not so hot.
6) Battery error
The robot lawnmower reports an error if the battery
is defective. Replace the battery with a new original
battery with the same specications as the defective
battery.
If the battery indicator light lights up red instead,
the battery simply needs charging. Carry the robot
lawnmower to the charging station and manually
charge it.
7) Charging error
The robot lawnmower has returned to the charging
station but it cannot be charged.
Check that the charging poles are clean and are
correctly inserted into the charging socket on the robot
lawnmower.
If the battery is at, you must perform manual charging.
Manual charging
Pull the robot lawnmower out of the charging station.
Move the main switch to the OFF position and wait 5
seconds.
Set the main switch to the ON position and push the
robot lawnmower into the charging station again. Do
NOT switch the robot lawnmower on using the Power
button (a)!
If the indicator light on the charging station does
not change to red at the rst attempt, pull the robot
lawnmower out of the charging station and push it back
in again. Repeat this until the indicator light turns red.
If this does not work after 10-15 times, allow the robot
lawnmower to remain in the charging station for an
hour before trying again.
When the indicator light on the charging station
lights up green, charging is complete and the robot
lawnmower is fully charged.
Remember to switch the robot lawnmower on after
charging it, unless you intend to put it into winter
storage.
8) PCB overheating
The robot lawnmower reports an error if the PCB
overheats. The robot lawnmower returns to the
charging station and allows the PCB to return to a safe
temperature.
The risk of this is greatest in summer, when the outside
temperature in direct sunlight approaches 35 °C. It may
be a good idea to change the start time of the robot
lawnmower so that it starts earlier in the day when it is
not so hot.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grouw 17940 - S600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grouw 17940 - S600 in the language / languages: English, German, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 18.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info