788793

Grouw 17937 Manual

60
Zoom out
Zoom in
Previous page
1/165
Next page
60
Note!
Do not short-circuit the rain sensor!
Note!
In the event of a thunderstorm, the charging station
must be disconnected from the mains and the robot
must be pulled out of the charging station.
Damage caused by lightning strike is not covered by the
warranty.
Error messages and troubleshooting
You can see by the error indicator light (h) what is wrong
if the robot lawnmower has stopped.
Indicator light Faults
Lights up red 1) The robot lawnmower has been
lifted
2) The robot lawnmower is stuck
3) Skirt error
Flashes red 4) Boundary wire signal error
Lights up blue 5) Battery error
Flashes blue 6) Abnormal battery temperature
7) PCB overheating
8) Charging error
9) The robot lawnmower has
rolled over
10) The robot lawnmower has been
overloaded
11) There is an obstruction on the
boundary wire
The errors are described below.
1) The robot lawnmower has been lifted
The robot lawnmower will report an error if the lift
sensors are continuously activated for 10 seconds.
Press the OK button to re-start the robot lawnmower.
If the error occurs repeatedly, you should check the
work area.
Remove any obstacles of over 100 mm, as these may
cause the robot lawnmower to roll over.
Use a regular lawnmower to cut grass that is taller than
60 mm.
2) The robot lawnmower is stuck
The robot lawnmower reports an error if the obstacle
sensors are activated more than 5 times in one minute.
Press the OK button to re-start the robot lawnmower.
If the error occurs repeatedly, investigate whether the
boundary wire is laid out correctly, as the error often
occurs in places that are too narrow or too cramped for
the robot lawnmower to move forward after changing
direction.
Also check whether there are obstacles such as
branches, etc. that may be restricting the robot
lawnmower’s freedom of movement.
3) Skirt error
There are four magnets in the robot lawnmower’s skirt.
If any metal comes between the magnets and the skirt,
the robot lawnmower may report an error.
Remove any pieces of metal.
Press the OK button to re-start the robot lawnmower.
4) Boundary wire signal error
The robot lawnmower will rotate a number of times,
stop and report an error if it goes outside the work area
or if there is an error with the boundary wire.
Check that all of the robot lawnmower is within the
work area and then check the indicator light on the
charging station:
Indicator light Indicates
O The charging station is not plugged
in.
Lights up
green (symbol
1)
The boundary wire is connected
correctly, the robot lawnmower
is ready and the battery is fully
charged.
Flashes green
(symbol 2+3)
There is a break in the boundary
wire.
The ends of the boundary wire are
connected the wrong way around on
the charging station.
Correct the error.
Lights up red
(symbol 4)
The battery is charging.
Flashes green
and red
alternately
Maintenance charging of battery
(trickle charging).
4 3 2 1
… 60 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grouw 17937 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grouw 17937 in the language / languages: English, German, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 17.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info