505550
13
Zoom out
Zoom in
Previous page
1/28
Next page
Speaker connection
Adjusting the audio level
For the best performance, you must set LEVEL (MIN/MAX) on the side of the amplifier to adjust
the level of the audio signals.
1. Use a screwdriver to turn LEVEL(MIN/MAX) fully to MIN
2. Turn the auto sound system’s volume control to about two-third of its full range.
3. Adjust LEVEL(MIN/MAX) to a comfortable listening level
4. Turn up the auto sound system’s volume control until the sound begins to distort.
Then immediately turn the volume down to a point just before where the distortion
began.
Caution: Never turn up the auto sound system’s volume control more than needed to
adjust the audio level, more than two thirds of its maximum volume.
5. Adjust LEVEL (MIN/MAX) until the sound is at the maximum level you want the
amplifier two produce.
6. Adjust the auto sound system’s volume control to a comfortable listening level.
Trouble shooting
This power amplifier has protection features to prevent any damages from misuse or faulty conditions. If the unit
senses excessive heat, short circuited speakers or overload, the protection indicators will light, and the system will
be turned off. In order to check the occurred problem, you should turn all levels down and all power off and
carefully check the installation for wiring mistakes or short. If the amplifier shuts down due to excessive heat, the
protection indicators will not light: simply allow time for the unit to cool.
Before removing your amplifier, refer to the list below and follow the suggested procedures.
Always test the speakers and their wires first.
Problem Check points
Amplifier is
not powered up
Check that there is battery power on the +12V terminal.
Check that remote terminal has at least +12V DC remote
connection.
Check a good ground connection. Check all fuses.
Check the protection LED is not lit.
Protection LED
illuminates when
amplifier is powered up
Check shorts on speaker wires.
Remove speaker wires and reset the amplifier. If the
protection LED still comes on, then the amplifier is faulty.
Fuse blowing
Check that the minimum speaker impedance is correct.
Check short on power cable and vehicle chassis.
Overheating
Check that the minimum speaker impedance is correct.
Check speaker shorts.
Check that there is a good airflow around the amplifier.
Sound too low /
Distorted sound
Check that the input level control is set to match the output
level of the unit.
Check the head unit volume.
Check speaker shorts.
Check that crossover frequencies have been properly set.
High hiss /
engine noise
in speakers
Check a good ground and for speaker shorts.
Disconnect all RCA inputs from the amplifier. If hiss/noise
disappears, check it with a good RCA interconnect. Then
check the component driving the amplifier.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ground zero GZUA 2250DX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ground zero GZUA 2250DX in the language / languages: German as an attachment in your email.

The manual is 3,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info