505567

Ground zero GZTA 5125X Manual

11
Zoom out
Zoom in
Previous page
1/40
Next page
5
Controls and functions – GZTA 5125X
6
Controls and functions
1 Speaker terminals For connection of the speakers
2
Power terminals
GND -> Ground connection
REM -> Remote antenna terminal
BATT -> +12 Volt
3 Satus indication
GREEN
–
OK
RED – Error
4 Cinch inputs
Terminal for connection of the RCA wires.
To avoid failure, please use high quality RCA wires.
5 Input level controlle
r
With this controller you can adjust the input sensitivity.
6 Mode switch
A
djust the crossover for the chosen utilization.
LPF – Only bass frequencies (below 40Hz - 4000Hz) (G
ZTA 5120X
Channel 5: 40Hz – 250Hz) will be reproduced.
FULL – All frequencies will be reproduced.
HPF – Only middle and high frequencies (
GZTA 5125X
: over 5 Hz –
4000 Hz /
GZTA 5120X
: over 40 Hz – 4000 Hz ) will be reproduced.
GZTA 5125X:
At LPF adjustment, also the Highpass (Subsonic) is activated.
This equals a Bandpass filter of 5 – 4000 Hz.
7 Low pass controller
Only frequencies from 40 Hz to 4000 Hz (
GZTA 5120X
Channel 5: 40
Hz – 250 Hz) will be reproduced (depending on the LPF filter controller
position). Set the filter switch to „LOW“ (“LP”) position. Adjust the
variable LPF frequency to the desired frequency using the controller.
8
High Pass controller
(Subsonic)
Set the filter switch to „HIGH“ position.
Adjust the variable HPF crossover frequency to the desired frequency
using the controller. All frequency between 5 and 4000 Hz (
GZTA
5120X
: 40 Hz – 4000 Hz) will be reproduced.
9 Filter controller
Depeding on the mode switch position, High- or Lowpassfilter can be
adjusted in a range from 40 Hz – 4000 Hz with this controller.
10
Subsonic controller
(GZTA 5120X Channel 5)
For adjusting the subsonic filter in a range from 10 Hz to 50 Hz.
11 Input mode switch
This switch allows you to choose the number of used cinch inputs.
A
ll
6 channels of
GZTA 5125X
can be operated with a 2- channel Cinch
cable.
You can chose if the 5
th
channel of
GZTA 5120X
should be operated
with Cinch input 5/6 or the summation of input 1/2/3/4.
12 Phase Shift controller
This controller allows you to fit the subwoofer channel of
GZTA 5120X
in-phase to the front system.
14 Remote control input For connection of the bass remote control.
Input Mode GZTA 5125X
2: This adjustment allows you to operate all 6 channels using the Cinch- Input Ch 1 and Ch 2. This is
recommended for active operation of a 3 way front system. For using this possibility, connect for example the
front cinch output of your headunit to the Ch 1/2 of the amplifier.
4: The channels 5 and 6 will be operated using the summarized signal from channel 1/2 and 3/4.
This mode is suggestive if channel 5 and 6 are only used as subwoofer channels.
For using this possibility, connect for example the front and rear cinch output of your headunit to the Ch 1/2 and
Ch 3/4 of the amplifier.
6: This adjustment allows you to operate every channel with an own signal. Using this possibility, every channel
can be adjusted by your head unit or processor separately.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ground zero GZTA 5125X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ground zero GZTA 5125X in the language / languages: German as an attachment in your email.

The manual is 1,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info