505539
11
Zoom out
Zoom in
Previous page
1/17
Next page
Trouble shooting
This power amplifier has protection features to prevent any damages from misuse or faulty
conditions. If the unit senses excessive heat, short circuited speakers or overload, the protection
indicators will light, and the system will be turned off. In order to check the occurred problem,
you should turn all levels down and all power off and carefully check the installation for wiring
mistakes or short. If the amplifier shuts down due to excessive heat, the protection indicators will
not light : simply allow time for the unit to cool.
Before removing your amplifier, refer to the list below and follow the suggested procedures.
Always test the speakers and their wires first.
Problem Check points
Amplifier is
not powered up
Check that there is battery power on the +12V
terminal.
Check that remote terminal has at least +12V
DC remote connection.
Check a good ground connection. Check all
fuses.
Check the protection LED is not lit.
Protection LED
illuminates when
amplifier is powered up
Check shorts on speaker wires.
Remove speaker wires and reset the amplifier.
If the protection LED still comes on, then the
amplifier is faulty.
Fuse blowing
Check that the minimum speaker impedance is
correct.
Check short on power cable and vehicle
chassis.
Overheating
Check that the minimum speaker impedance is
correct.
Check speaker shorts.
Check that there is a good airflow around the
amplifier.
Sound too low /
Distorted sound
Check that the input level control is set to
match the output level of the unit.
Check the head unit volume.
Check speaker shorts.
Check that crossover frequencies have been
properly set.
High hiss /
engine noise
in speakers
Check a good ground and for speaker shorts.
Disconnect all RCA inputs from the amplifier.
If hiss/noise disappears, check it with a good
RCA interconnect. Then check the component
driving the amplifier.
Specifications
Model GZPA 1.6500SPL GZPA 1.10000SPL
RMS power @ 1 , 10% THD
CEA Standard CEA-2006-A
1 x 6500W 1 x 9500W
RMS power @ 1 , 1% THD
CEA Standard CEA-2006-A
1 x 5800W 1 x 8300W
RMS power @ 2 , 1% THD
CEA Standard CEA-2006-A
1 x 3400W 1 x 4800W
RMS power @ 4 , 1% THD
CEA Standard CEA-2006-A
1 x 1800W 1 x 2600W
RMS power @ 1 18 V,
10% THD
1 x 8000W 1 x 11000W
RMS power @ 2 Linkmode
14,6 V, 1% THD
1 x 11000 W 1 x 15000W
Damping factor >170 (100Hz @ 4 ) >250 (100Hz @ 4 )
Signal to noise ratio >65 dB >65 dB
Lowpass crossover 35Hz ~ 250Hz 35Hz ~ 250Hz
Subsonic Filter 10Hz ~ 70Hz 10Hz ~ 70Hz
Bass boost 0 ~ +9dB 0 ~ +9dB
Bass boost Frequency 30Hz ~ 90Hz 30Hz ~ 90Hz
Phase shift 0 ~ 180° 0 ~ 180°
Frequency range
10 Hz ~ 250 Hz
(+/- 1dB)
10 Hz ~ 250 Hz
(+/- 1dB)
Efficiency @ 4 86% 86%
Input sensitivity 200mV to 10V (+/- 5%) 200mV bis 10V (+/- 5%)
Dimensions
W x H x L mm
625 x 75 x 300 mm 870 x 75 x 300 mm
Dimensions
W x H x L inch
24.61” x 2.95” x 11.81” 34.25” x 2.95” x 11.81”
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ground zero GZPA 1.6500SPL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ground zero GZPA 1.6500SPL in the language / languages: German as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info