568392
14
Zoom out
Zoom in
Previous page
1/20
Next page
14
Allgemeines
!
!
!
!
Sender und Empfänger
sind ab Werk bereits
vorprogrammiert. Jeder
Sender hat einen
eigenen Code, so dass
eine Störung durch
andere Sender
ausgeschlossen ist
In einem Empfänger
können bis zu 20 Sender
einprogrammiert werden.
Ein Sender kann jedoch
an beliebig vielen
Empfängern angelernt
werden
Das Bild zeigt einige der
vielen Kombinations-
Möglichkeiten. Unter
anderem kann jeder
Empfänger individuell
oder zentral angesteuert
werden
Jedem Sender kann eine
andere Melodie zur Ruf-
Unterscheidung
zugeordnet werden
General
!
!
!
!
The transmitter and
receiver are already pre-
programmed ex works.
Each transmitter has an
individual code so
that interference from
other transmitters is
excluded.
Up to 20 transmitters
can be programmed into
one receiver. However,
one transmitter can be
tuned to any desired
number of receivers.
The figure shows a few of
the many possible
combinations. Each
receiver can be triggered
individually or centrally,
for example.
A different melody can
be allocated to each
transmitter to make it
possible to distinguish
between them.
Généralités
!
!
!
!
L'émetteur et le récepteur
sont déjà préprogram-
més en usine. Chaque
émetteur a un code prop-
re, ce qui exclut toute
perturbation provoquée
par d'autres émetteurs.
Dans un récepteur, il est
possible de programmer
jusqu'à 20 émetteurs.
Un émetteur peut être
programmé sur un
nombre infini de
récepteurs.
La figure montre quel-
ques-unes des nombreu-
ses possibilités de com-
binaison. Entre autres,
chaque récepteur peut
être commandé
individuellement ou de
façon centralisée.
A chaque récepteur, il est
possible d'affecter une
autre mélodie pour
établir une distinction des
appels.
Algemeen
!
!
!
!
De zender en ontvanger
zijn vanaf de fabriek
reeds voorgeprogram-
meerd. Iedere zender
heeft een eigen code,
zodat een storing door
andere zenders
uitgesloten is.
In een ontvanger kunnen
max. 20 zenders gepro-
grammeerd worden.
Een zender kan echter
op willekeurig veel ontv.
aangeleerd worden.
De tekening toont enkele
van de vele combinatie-
mogelijkheden. Onder
andere kan elke
ontvanger individueel of
centraal worden
aangestuurd.
Aan iedere zender kan
een andere melodie
worden toegekend om de
verschillen in de
oproepen te kunnen
aangeven.
BEDIENUNG
Programmierung
BEDIENING
Programmering
UTILISATION
Programmation
OPERATION
Programming
GB
F
D NL
Programmierung neuer
Sender
(LEARN-Funktion)
!
!
!
!
!
!
Wir empfehlen, Sender
und Empfänger zu
programmieren, bevor
sie an der Wand befestigt
werden
Taste T1 ca. 3 Sekunden
gedrückt halten, bis
grüne LED 1 leuchtet
Taste des neuen Senders
kurz drücken
Der Empfänger spielt als
Empfangsbestätigung
eine Melodie ab, die LED
1 erlischt. Bei Bedarf
andere Melodie mit Taste
T2 einstellen (siehe
oben)
Falls kein Sender erkannt
wird, fängt die LED 1
nach ca. 15 sec. an zu
blinken und erlischt nach
weiteren 10 sec. Vorgang
dann wiederholen
ACHTUNG! Der Power-
Sender PSE... benötigt
aus technischen
Gründen einen Mindest-
Abstand von 3m zum
Empfänger!
Programming new
transmitters
(LEARN function)
!
!
!
!
!
!
We recommend
programming trans-
mitters and receivers
before they are fixed on
the wall
Hold down button T1
for approx. 3 seconds
until the green LED 1
goes on
Press the button on the
new transmitter briefly.
The receiver plays a
melody as confirmation
of receipt, LED 1 goes
out. If required, set a
different melody using
button T2 (see above).
If no transmitter is
detected, LED 1 starts
to flash after approx.
15 sec. and switches off
after another 10 sec. Then
repeat process.
ATTENTION! For
technical reasons, the
PSE… power transmitter
requires a minimum
distance of3mtothe
receiver!
Programmation de
nouveaux émetteurs
(fonction LEARN)
!
!
!
!
!
!
Nous recommandons de
programmer les éme-
teurs et les récepteurs
avant de les fixer à la
paroi.
Maintenir la touche T1
enfoncée pendant en-
viron 3 secondes jusqu'à
ce que la LED 1 verte
s’allume.
Presser brièvement la
touche du nouvel
émetteur.
Le récepteur joue une
mélodie à titre de confir-
mation de réception, la
LED 1 s'éteint. Si
nécessaire, régler une
autre mélodie avec la
touche T2 (voir pl. haut).
Si aucun émetteur n'est
détecté, la LED 1 com-
mence à clignoter après
15 sec. Répéter ensuite
le processus.
ATTENTION ! Pour des
raisons techniques,
l’émetteur Power PSE...
doit être positionné à au
moins 3 m du récepteur !
Programmeren van
nieuwe zenders
(LEARN-functie)
!
!
!
!
!
!
Wij adviseren de zender
en ontvanger te
programmeren voordat
deze aan de wand
bevestigd wordt.
Toets T1 ca. 3 seconden
lang ingedrukt houden tot
de groene LED 1 brandt.
Toets van de nieuwe
zender kort indrukken.
De ontvanger speelt als
ontvangstbevestiging
een melodie af, de LED 1
gaat uit. Desgewenst
andere melodie met toets
T2 instellen (zie boven).
Indien er geen zender
wordt herkend, begint de
LED 1 na ca. 15 sec. aan
te knipperen. Proces dan
herhalen.
ATTENTIE! De Power-
Zender PSE... dient om
technische redenen een
afstand van tenminste
3m op de ontvanger te
hebben.
V5
LED 1
T1
4
Press
3
2
T1
LED 1
V1 V2 V3 V4
1
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grothe MISTRAL 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grothe MISTRAL 300 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info