740723
7
Zoom out
Zoom in
Previous page
1/12
Next page
7
GB
F
D NL
LED 1
T 1
7a
MODE Kanal/Channel 2
(ALARM-Funktion)
!Diese Funktion ist dann
interessant, wenn z.B.
ein Bewegungsmelder
angeschlossen ist, der
tagsüber eine Melodie
auslösen soll, nachts
hingegen einen ALARM-
Ton (z.B. in Geschäften)
!Diese MODE-Funktion
kann nur für Kanal 2 (d.h.
für die an den Klemmen
C2 bzw. CT 2
angeschlossenen Tasten)
genutzt werden
!Im Grundzustand
erzeugt Kanal 2 genau
wie Kanal 1 eine
Melodie. In diesem Fall
blinkt die grüne LED 1
nicht.
!Nach einmaligem
Betätigen von Taste T1
ist die ALARM-Funktion
aktiviert. LED 1 blinkt
dann regelmäßig zwei
Mal.
!Nach nochmaligem
Betätigen von Taste T1
wird Kanal 2 gänzlich
ausgeschaltet. LED 1
blinkt dann regelmäßig
ein Mal
!Wird Taste T1 nochmals
betätigt, wird der
Grundzustand (Melodie)
wiederhergestellt. LED 1
blinkt nicht mehr
Stummschaltung
(MELODY off-Funktion)
!Taste T2 länger als 3
Sekunden gedrückt
halten, bis LED 2
aufleuchted
!Die rote Kontroll-LED 2
blinkt zur Erinnerung
regelmäßig
!Nun sind für Kanal 1
und 2 alle Melodien
stummgeschaltet. Wurde
jedoch vorher über Taste
T1 die ALARM-Funktion
eingestellt (siehe oben),
so ist diese Funktion
weiterhin aktiv.
!Wiedereinschalten
durch kurzes Betätigen
von Taste T2
Fonctionnement muet
(fonction MELODY off)
!Maintenir la touche T2
enfoncée pendant plus
de 3 secondes jusqu'à ce
que la LED 2 clignote.
! La LED 2 de contrôle
rouge clignote à titre de
rappel.
!Le son de toutes les
mélodies est à présent
désactivé pour les
canaux 1 et 2. Toutefois,
si vous avez auparavant
réglé la fonction
ALARME via la touche
T1 (voir ci-dessus), cette
fonction reste active.
!Remise en circuit par
activation brève de la
touche T2.
Silent Operation
(MELODY off-function)
!Continue pressing
button T2 for more than
3 seconds, until LED 2
flashes.
!The red warning light
LED 2 now flashes as a
reminder
!All melodies for
Channel 1 and Channel 2
are now silenced.
However, if the ALARM
function was previously
activated with button T1
(see above), this function
remains active.
!Switch on again by
pressing button T2
briefly.
Stomschakeling
(MELODY off-functie)
!Toets T2 langer dan 3
se-conden ingedrukt
houden tot LED 2
knippert.
!De rode controle-LED 2
knippert ter herinnering.
!Nu zijn voor kanaal 1 en
2 alle melodieën
uitgeschakeld. Als echter
tevoren via toets T1 de
ALARM-functie ingesteld
is (zie boven), dan is
deze functie ook daarna
nog actief.
!Opnieuw inschakelen
door kort bedienen van
toets T2.
MODE Kanaal/Channel 2
(ALARM-functie)
!Deze functie is dan
interessant als bijv. een
bewegingsmelder
aangesloten is, die
overdag een melodie
moet activeren en‚ s
nachts daarentegen een
ALARM-toon.
!Deze MODE-functie
kan alleen voor kanaal 2
(d.w.z. voor de aan de
klemmen C2 c.q. CT 2
aangesloten toetsen)
gebruikt worden.
!Op de basisstand laat
kanaal 2 net als kanaal 1
een melodie horen. In dat
geval knippert de groene
LED 1 niet.
!Nadat toets T1 één keer
is gebruikt, is de ALARM-
functie geactiveerd. LED
1 knippert dan regelmatig
twee keer.
!Na toets 1 nog een keer
gebruikt te hebben wordt
kanaal 2 helemaal
uitgeschakeld. LED 1
knippert dan regelmatig
een keer.
!Als toets T1 nog een
keer wordt gebruikt,
wordt de basistoestand
(melodie) weer ingesteld.
LED 1 knippert niet meer.
Canal MODE / Channel 2
(fonction ALARME)
!Cette fonction est
intéressante lorsque, par
exemple, vous raccordez
un détecteur de
mouvement qui
déclenche une mélodie
durant la journée et une
sonnerie d'ALARME
durant la nuit.
!Cette fonction MODE
ne peut être utilisée que
pour le canal 2 (c.-à-d.
pour les touches
raccordées aux bornes
C2 ou CT2).
!Dans l'état initial, le
canal 2 produit une
mélodie tout comme le
canal 1. Dans ce cas, la
DEL 1 verte ne clignote
pas.
!Après avoir appuyé une
fois sur la touche T1, la
fonction ALARME est
activée. La DEL 1
clignote alors
régulièrement deux fois.
!Si vous appuyez encore
une fois sur la touche T1,
le canal 2 est
entièrement désactivé.
La DEL 1 clignote alors
régulièrement une fois.
!Si vous appuyez une
nouvelle fois sur la
touche T1, l'état initial
(mélodie) est rétabli. La
DEL 1 ne clignote plus.
Channel 2 MODE
(ALARM function)
!This function is
interesting if e.g. a
motion detector is
connected which
actuates a melody during
the day and an ALARM
function overnight.
!This MODE function
can only be used with
Channel 2 (i.e. for the
buttons connected to
terminals C2 and CT 2).
!In the normal state,
Channel 2 sounds a
melody, just as for
Channel 1. In this case,
the green LED 1 does
not flash.
!Actuating button T1
activates the ALARM
function. LED 1 then
flashes twice at regular
intervals.
!Actuating button T1
again switches off
Channel 2 altogether.
LED 1 then flashes once
at regular intervals.
!Actuating button T1
once again restores the
normal state (melody).
LED 1 then no longer
flashes.
LED 2
T 2
Blink
7b
(variiert je nach Type)
VOLUME
T1
Press Press
T2
Melody
Alarm
Off
<1 sec: ALARM
CH2
Blink
VOLUME
>3 sec: MUTE
T1
Press Press
T2
MUTE
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grothe Croma 231A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grothe Croma 231A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info