626604
5
Zoom out
Zoom in
Previous page
1/12
Next page
2
Electrical installation
Electrical installation work must only be performed
by a qualified electrician. This work must be
carried out in accordance with the regulations
according to IEC 60364-7-701 (corresponding
to VDE 0100 Part 701) as well as all national and
local regulations.
Extension cables are not permitted between the electrical
socket and boiling water storage heater connection.
Installation
Refer to the dimensional drawing on fold-out page I.
Installing fitting, see fold-out page II, Figs. [1] and [2].
Insert fitting in sink hole. This will require leading through the
hoses one at a time.
Note: If there is no need to fit support plate (A), the clamping
length may be increased by 15mm, see Fig. [1].
Mount safety relief valve kit to the waste pipe, see Figs. [3]
to [6].
Mount wall holder, see Figs. [7] and [8].
Mount compression couplings (B) and tighten nipple, see
Fig. [9].
Fix expansion vessel (C) with safety assembly to the wall
holder, see Fig. [10].
Connect filter head and filter, see technical product
information for the filter head and the filter cartridge and fold-
out page III, Fig. [11]. Note direction of flow.
1. Install pressure hose (D) to the inlet of filter head.
2. Install sensor (E) at outlet of filter head. The sensor (E) must
be installed horizontally.
3. Install display unit (F).
Use suitable screws and wall plugs (not included in the scope
of delivery).
Connect filter system, see Fig. [12].
1. Connect adaptor (G) on the cold-water service valve.
2. Screw pressure hose (D) of filter system onto adapter (G).
3. Screw hose (H) onto sensor (E).
Connect storage heater, see Figs. [2] and [13].
Install storage heater taking into consideration the
available hose lengths.
Do not connect voltage supply yet.
Flush pipes thoroughly before and after installation
(observe EN 806).
1. Connect expansion vessel (C), see Fig. [13].
2. Screw hose (H) to expansion vessel (C).
3. Screw storage heater pressure hose (I) marked blue to
expansion vessel (C) using the seals provided.
4. Connect copper pipe (not in the scope of delivery) to
the Ø15mm compression connection (J) of the expansion
vessel (C) and tighten.
Connecting fitting, see fold-out page III, Fig. [14].
1. Screw fitting pressure hose (K) marked blue to adapter (G).
2. Screw red marked pressure hose (L) of the fitting onto the
hot-water service valve.
3. Connect the fitting pressure hose (M) marked 99 °C to
connection (N) on the storage heater.
Open the service valve and check connections for
watertightness.
Filling storage heater with water, see Figs. [15] and [16].
1. Pull button (O1) on handle (O) of fitting outward and turn the
handle anti-clockwise, see Fig. [15].
2. Fill the storage heater until water comes out the spout of
the fitting.
3. Connect voltage supply via mains plug (P), see Fig. [16].
4. Press and hold button (Q) on storage heater for at
least 2 seconds to switch on the storage heater. The red
indicator lamp (Q1) indicates that the storage heater is
switched on.
Important!
The spout must not be fitted with any downstream
resistances in the form of air bubblers (e.g. mousseurs) or
components reducing flow (e.g. restrictors) as these will
result in damage to the storage heater.
Set water hardness at filter head, see fold-out page IV,
Fig. [17].
Set water hardness at bypass setting of filter head to local
conditions, see table column A on page 4.
The relevant water supplier can provide information on the
water hardness.
The bypass value setted to the filter head must also be set on
the display unit (F), see Fig. [18].
Setting the litre specification (factory setting is 600 litre),
see Fig. [18].
The value for the litre specification depends on the water
hardness as per table column B on page 4:
The GROHE Red boiling water system is now fully
installed and ready for operation.
Button Display
Briefly press PROG button
(PRG flashes)
Briefly press RESET button to access
programming for litre specification
(00000 flashes)
Keep pressing PROG button until
required position is reached
(00000 digit flashes)
Keep pressing RESET button until
required digit is reached
(00600 digit flashes)
Keep pressing PROG button to exit
menu (PRG disappears and set value
appears)
The date of installation must be noted on the
maintenance sticker and affixed at a visible location
on the storage heater.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grohe Red Duo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grohe Red Duo in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Grohe Red Duo

Grohe Red Duo Installation Guide - All languages - 86 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info