759838
5
Zoom out
Zoom in
Previous page
1/48
Next page
2
Funktionseinheit spülen, siehe Klappseite II und III,
Abb. [10] und [11].
1. Verschlussschraube (D) herausschrauben, siehe
Klappseite II Abb. [10].
2. Rückflussverhinderer (E) und Sieb (F) herausnehmen.
3. Spülstopfen (G) in den freien Sitz des Rückflussverhinderers
einschrauben, siehe Klappseite III, Abb. [11].
4. Kalt- und Warmwasserzufuhr öffnen.
Rohrleitungssystem vor und nach der Installation
gründlich spülen (DIN 1988 / DIN EN 806 beachten)!
5. Kalt- und Warmwasserzufuhr schließen und die
Spülstopfen (G) entfernen, siehe Abb. [11].
6. Sieb (F) und Rückflussverhinderer (E) einsetzen, siehe
Klappseite II, Abb. [10].
7. Verschlussschraube (D) einschrauben.
Kalt- und Warmwasserzufuhr öffnen und Anschlüsse
auf Dichtheit prüfen.
8. Deckel aufsetzen und mit Schrauben befestigen, siehe
Abb. [5].
Wartung
Alle Teile prüfen, reinigen, evtl. austauschen.
Spannungsversorgung unterbrechen!
Vorabsperrungen schließen.
I. Thermostat-Kompaktkartusche, siehe Klappseite II
und III, Abb. [5] und [12].
1. Schrauben herausdrehen und Deckel abnehmen, siehe
Klappseite II, Abb. [5].
2. Schraube (H) herausdrehen und Scheibe (H1) abnehmen,
siehe Klappseite III, Abb. [12].
3. Stecker (J1) lösen und Stellmotor (J) abziehen.
4. Schraubring (K) mit Werkzeug 34mm lösen und
abschrauben.
5. Thermostat-Kompaktkartusche (L) gegebenenfalls
über die Ausnehmung (L1) aushebeln.
Montage in umgekehrter Reihenfolge.
Einbaulage der Thermostat-Kompaktkartusche (L)
beachten, siehe Detail (L2).
6. Stecker (J1) mit Stellmotor (J) verbinden.
7. Spannungsversorgung herstellen und Kalt- und Warmwas-
serzufuhr öffnen, siehe Klappseite II, Abb. [7] und [9].
8. Reguliermutter (M) drehen bis 38 °C in der Anzeige des
Bedienpaneels der Armatur angezeigt werden, siehe
Klappseite III, Abb. [12].
9. Stellmotor (J) montieren.
Nach jeder Wartung an der Thermostat-Kompaktkartusche
ist eine Justierung auf 38 °C erforderlich.
II. Rückflussverhinderer (E), siehe Klappseite III, Abb. [12].
1. Verschlussschraube (D) herausschrauben.
2. Rückflussverhinderer (E) und Sieb (F) herausnehmen.
III. Servomotor (N), siehe Klappseite III, Abb. [13].
Stecker (N1) lösen, Clip (N2) abziehen und Servomotor (N)
herausziehen.
IV. Magnetventil (O), siehe Klappseite III Abb. [13].
Stecker lösen (O1), Klammer (O2) abziehen und
Magnetventil (O) herausziehen.
Montage in umgekehrter Reihenfolge.
Ersatzteile
Siehe Klappseite I (* = Sonderzubehör).
GB
Safety notes
Avoid danger due to damaged external transformer
connection cables. In the case of damage, the
external transformer connection cable must be
replaced by the manufacturer or his customer
service department or an equally qualified person.
Installation is only possible in frost-free rooms.
The plug power supply is only suitable for indoor use.
The function unit and plug-in connectors must not be
directly or indirectly sprayed with water when cleaning.
The voltage supply must be separately switchable.
Applications
Thermostatic mixers are designed for hot water supplies from
pressurised storage heaters and offer the highest temperature
accuracy when used in this way. With sufficient power output
(from 18 kW or 250 kcal/min), electric or gas instantaneous
heaters are also suitable.
Thermostats cannot be used in connection with unpressurised
storage heaters.
All thermostats are adjusted in the factory at a flow pressure
of 0.3 MPa on both sides.
Technical Data
Flow pressure:
- Minimum flow pressure without downstream
resistances: 0.05 MPa
- Minimum flow pressure with downstream
resistances: 0.1 MPa
- Recommended 0.1 - 0.5 MPa
Operating pressure max.: 1.0 MPa
Test pressure: 1.6 MPa
If static pressures exceed 0,5 MPa, a pressure-reducing
valve must be installed.
Avoid major pressure differences between hot and cold
water supply.
Flow rate at 0.3 MPa flow pressure
(with simultaneous use of all outlets): approx. 51 l/min
Minimum flow rate: 5 l/min
Hot water supply temperature: max. 80 °C
Recommended (energy saving): 60 °C
Hot water temperature at supply connection min. 2 °C
higher than mixed water temperature.
Voltage supply: 230 V AC, 50/60 Hz
(plug power supply 230 V AC/6 V DC)
Type of protection: - Function unit IP 40
- Plug power supply IP 40
Water connection: COLD
HOT
Electrical test data
Software class: B
Contamination class: 2
Rated surge voltage: 2500 V
Temperature for ball impact test: 100 °C
The test for electromagnetic compatibility (interference
emission test) was performed at the rated voltage and
rated current.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grohe 36067 Ondus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grohe 36067 Ondus in the language / languages: All languages as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info