708317

Greenworks GD40CS - 20077 Manual

23
Zoom out
Zoom in
Previous page
1/256
Next page
20
English
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
SHARPENING THE SAW CHAIN
See figure 16 - 21
When the chain penetrates into wood with difficulty, it
needs sharpening as follows:
Put the chain under tension.
Fasten the bar in a vice so that the chain can slide.
Fasten the file to the file holder and place it on cutter
at 35° angle.
File with forward strokes only until all the worn out
parts of the cutting edge are taken away.
Count the number of strokes given to the cutter as
a reference and file away with the same number of
strokes on all other cutters.
If the depth gauge protrudes from the template after
sharpening a few times, reset its level. Use a flat file.
Finally, round off the depth gauge.
NOTE: It is recommended to have the deep or important
sharpening carried out by a service agent who is equipped
with electric sharpener.
GUIDE BAR MAINTENANCE
When you have finished working, clean out the groove
and the oil passages with a scraping hook.
Periodically trim the sides of rails using a flat file. If not
done in the long run, the feather edges might break
away and damage the bar.
If one rail is higher than the other one, it is necessary
to make it even with a flat file then smooth it with a file
or fine grain abrasive paper.
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing
any maintenance.
GENERAL MAINTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call Greenworkstools Customer
Service for assistance.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake liquids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an authorised service centre.
STORAGE
STORING THE PRODUCT
Remove the battery pack from he unit before storing.
Clean all foreign material from the unit.
Store it in a place that is inaccessible to children.
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery pack life.
Never store batteries in a discharged condi ion. Store
battery packs in a 30%-50% charged condition.
Store the battery pack where the temperature is below
27 FIC and away from moisture.
All batteries gradually lose heir charge. The higher
the temperature, the quicker they lose their charge.
If you store your unit for long periods of time without
using it, charge the pack as normal every six months
of storage. This prac ice will prolong battery pack life.
DISPOSAL
Power tools and accessories contain
large amount of valuable resources
and plastics that can be recycled.
Waste electrical products should not be
disposed of together with household
waste. Please recycle where facilities
exist. Check with your local authority or
retailer for recycling advice.
The
Li-ion battery. This product has been marked wi h a symbol
rela ing to separate collection for all battery packs and battery
pack. It will then be recycled or disman led in order to reduce
the impact on he environmrnt. Battery packs can be hazardous
for the enviroment and for human health.
battery contains material which is hazardous to you
and the environment. It must be removed and disposed
of separately at a facility that accepts lithium-ion batteries.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks GD40CS - 20077 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks GD40CS - 20077 in the language / languages: All languages as an attachment in your email.

The manual is 8,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info