708335

Greenworks G24ST - 2101207 Manual

5
Zoom out
Zoom in
Previous page
1/162
Next page
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SV HR HU RO BG EL AR TR HE LT LV ET
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing
any maintenance.
GENERAL MAINTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are
replaced.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake uids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an Authorised Service Centre.
SPOOL REPLACEMENT See Figure 12.
Use original manufacturer’s replacement cutting line for
best performance.
Remove the battery pack.
Push in tabs (C) on side of spool cover (A).
Pull spool cover up to remove.
Remove the old spool.
To install the new spool (B), make sure the cutting line
is captured in the slot on the new spool (F). Make sure
the end of the cutting line is extended approximately
15cm beyond the slot.
Install the new spool so that the cutting line and slot
align with the eyelet (E) in the cutting head (G). Thread
the cutting line into the eyelet.
Pull the cutting line extending from the cutting head so
the cutting line releases from the slot in the spool.
Reinstall the spool cover by depressing tabs into slots
(D) and pushing down until spool cover clicks into
place.
CUTTING LINE REPLACEMENT See Figure 13.
Remove the battery pack.
Remove the spool from the cutting head.
NOTE: Remove any old cutting line remaining on the
spool.
Cut a piece of cutting line approximately 3m long.
Insert the cutting line into the anchor hole (B) in the
upper part of the spool. Wind the cutting line around
the upper part of the spool clockwise, as shown by the
arrows on the spool. Place cutting line in the slot (C)
on upper spool flange, leaving about 15 cm. extended
beyond the slot. Do not overfill. After winding the cutting
line, there should be at least 0.635 cm between the
wound cutting line and the outside edge of the spool.
Replace the spool (A), and the spool cover. Refer to
spool replacement earlier in this manual.
4
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks G24ST - 2101207 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks G24ST - 2101207 in the language / languages: All languages as an attachment in your email.

The manual is 15,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info