Manual Greenworks G24LT30 - 21227 (page 5 of 160) (All languages)

708341

Zoom out

Zoom in

1/160

English

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

Only the parts shown on the parts list are intended to

be repaired or replaced by the customer. All other parts

should be replaced at an Authorised Service Centre.

CHARGER AND BATTERY PACK

29697/29807- 24V 43Wh Lithium battery pack

29837- 24V 86Wh Lithium battery pack

29817/29827- 24V charger

BATTERY PACK REMOVAL AND PREPARATION FOR

RECYCLING

Contact customer service for the latest replacement parts

and accessories.

WARNING

Upon removal, cover the battery pack’s terminals with

heavy-duty adhesive tape. Do not attempt to destroy

or disassemble battery pack or remove any of its

components. Lithium-ion and nickel-cadmium batteries

must be recycled or disposed of properly. Also, never

touch both terminals with metal objects and/or body

parts as short circuit may result. Keep away from

children. Failure to comply with these warnings could

■Install the new spool so that the cutting line and slot

align with the eyelet in the cutting head. Thread the

cutting line into the eyelet.

■Pull the cutting line extending from the cutting head

so the cutting line releases from the slot in the spool.

■Reinstall the spool cover by depressing tabs into slots

and pushing down until spool cover clicks into place.

CUTTING LINE REPLACEMENT

See Figures 12 - 13.

■Remove the battery pack.

EN DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

SPOOL REPLACEMENT

See Figure 12.

Use original manufacturer’s replacement cutting line for

best performance.

■Remove the battery pack.

■Push in tabs on side of spool cover.

■Pull spool cover up to remove.

■Remove the old spool.

■To install the new spool, make sure the cutting line is

captured in the slot on the new spool. Make sure the

end of the cutting line is extended approximately 15cm

beyond the slot.

■Remove the spool from the cutting head.

NOTE: Remove any old cutting line remaining on the

spool.

■Cut a piece of cutting line approximately 3m long. Use

only 1.65mm diameter monofilament cutting line.

■Insert the cutting line into the anchor hole in the upper

part of the spool. Wind the cutting line around the upper

part of the spool clockwise, as shown by the arrows on

the spool. Place cutting line in the slot on upper spool

flange, leaving about 15cm. extended beyond the slot.

Do not overfill. After winding the cutting line, there

should be at least 0.635 cm between the wound

■Replace the spool, and the spool cover. Refer to spool

replacement earlier in this manual.

STORING THE TRIMMER

■Remove the battery pack from the trimmer before

storing.

cutting line and the outside edge of the spool.

■Clean all foreign material from the trimmer.

■Store it in a place that is inaccessible to children.

■Keep away from corrosive agents such as garden

chemicals and de-icing salts.

■Store and charge your batteries in a cool area.

Temperatures above or below normal room

temperature will shorten battery pack life.

■Never store batteries in a discharged condition. Wait

for battery pack to cool and fully charge immediately.

■Store the battery pack where the temperature is below

27˚C and away from moisture.

■All batteries gradually lose their charge. The higher the

temperature, the quicker they lose their charge. If you

store your unit for long periods of time without using

it, recharge the batteries every month or two. This

practice will prolong battery pack life.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks G24LT30 - 21227 in the language / languages: All languages as an attachment in your email.

The manual is 69,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Greenworks G24LT30 - 21227 Manual

Product: