644720

Greenworks 25357 Manual

20
Zoom out
Zoom in
Previous page
1/238
Next page
18
Deutsch (Übersetzung der originalen Anleitungen)
DE
FR EN ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
18
English (Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
is properly seated with shaft going through center
blade hole and the two blade posts inserted into their
respective holes on the blade. Make sure it is installed
with the curved ends pointing up toward the mower
deck and not down toward the ground. When seated
properly, the blade should be flat against the blade
holder.
9. Replace the blade insulator and spacer, then thread
the blade nut on the shaft and finger tighten.
NOTE: Make certain all parts are replaced in the exact
order in which they were removed.
10. Torque the blade nut down clockwise using a torque
wrench (not provided) to ensure the bolt is properly
tightened. The recommended torque for the blade nut
is 62.5~71.5 kgfcm (350-400 in.-lb.).
REPLACING WHEELS
See figure 12.
To ensure smooth operation of wheels, the wheel
assembly should be cleaned before storage.
1. Remove the opening pins and the washers.
2. Remove the wheel and replace with new wheel.
3. Replace the washers, pins and the wheel covers.
STORING THE MOWER
To lower the handle before storing:
1. Fully loosen the handle knobs on the sides of the
handle and fold the upper handle down.
2. Push inward on each side of the lower handle, and
lift the sides of the lower handle past the edges of the
handle mounting brackets. Avoid pinching or trapping
any cables.
REPLACING THE BATTERY
The mower battery is designed for maximum life; however,
like all batteries, it will eventually need to be replaced.
Charge the new battery pack before use.
To install a new battery:
1. Remove the isolator key.
2. Carefully unlock and remove the battery pack.
3. Install the new battery pack.
4. Take the old battery pack to a recycling center that
accepts lead acid/lithium ion batteries. Never dispose
of battery in fire or regular household trash.
WARNING
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which may result in serious personal
injury.
Periodically check all nuts and bolts for proper tightness to
ensure safe operation of the mower.
Wipe the mower clean with a dry cloth occasionally. Do
not use water.
LUBRICATION
All of the bearings in this product are lubricated with a
suffi cient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore, no
further bearing lubrication is required.
WARNING
Always protect hands by wearing heavy gloves and/or
wrapping the cutting edges of the blade with rags and
other material when performing blade maintenance.
Contact with the blade could result in serious personal
injury.
WARNING
Do not lubricate any of the wheel components.
Lubrication may cause the wheel components to fail
during use, which could result in serious personal injury
to the operator and/or mower or property damage.
REPLACING THE CUTTING BLADE
See figure 10-11.
NOTE: Only use authorised replacement blades. Replace
worn or damaged blades and bolts in sets to preserve
balance.
1. Stop the motor and remove the isolator key. Allow
blade to come to a complete stop.
2. Remove the battery pack.
3. Turn the mower on its side.
4. Wedge a block of wood between the blade and mower
deck to prevent the blade from turning.
5. Loosen the blade nut by turning it counterclockwise
(as viewed from bottom of mower) using a 15 mm
wrench or socket (not provided).
6. Remove the blade nut, spacer, blade insulator, and
blade.
7. Make certain the blade holder is pushed completely
against the motor shaft.
8. Place the new blade on the shaft. Ensure blade
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks 25357 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks 25357 in the language / languages: All languages as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info