644599

Greenworks 25137 - 49Li Manual

20
Zoom out
Zoom in
Previous page
1/238
Next page
18
Deutsch (Übersetzung der originalen Anleitungen)
DE
FR EN ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
18
English (Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
REPLACING WHEELS
See figure 12.
To ensure smooth operation of wheels, the wheel
assembly should be cleaned before storage.
1. Remove the opening pins and the washers.
2. Remove the wheel and replace with new wheel.
3. Replace the washers, pins and the wheel covers.
STORING THE MOWER
To lower the handle before storing:
1. Fully loosen the handle knobs on the sides of the
handle and fold the upper handle down.
2. Push inward on each side of the lower handle, and
lift the sides of the lower handle past the edges of the
handle mounting brackets. Avoid pinching or trapping
any cables.
REPLACING THE BATTERY
The mower battery is designed for maximum life; however,
like all batteries, it will eventually need to be replaced.
Charge the new battery pack before use.
To install a new battery:
1. Remove the isolator key.
2. Carefully unlock and remove the battery pack.
3. Install the new battery pack.
4. Take the old battery pack to a recycling center that
accepts lead acid/lithium ion batteries. Never dispose
of battery in fire or regular household trash.
Periodically check all nuts and bolts for proper tightness to
ensure safe operation of the mower.
Wipe the mower clean with a dry cloth occasionally. Do
not use water.
LUBRICATION
All of the bearings in this product are lubricated with a
suffi cient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore, no
further bearing lubrication is required.
WARNING
Always protect hands by wearing heavy gloves and/or
wrapping the cutting edges of the blade with rags and
other material when performing blade maintenance.
Contact with the blade could result in serious personal
injury.
WARNING
Do not lubricate any of the wheel components.
Lubrication may cause the wheel components to fail
during use, which could result in serious personal injury
to the operator and/or mower or property damage.
REPLACING THE CUTTING BLADE
See figure 10-11.
NOTE: Only use authorised replacement blades. Replace
worn or damaged blades and bolts in sets to preserve
balance.
1. Stop the motor and remove the key. Allow blade to
come to a complete stop.
2. Remove the battery pack.
3. Turn the mower on its side.
4. Wedge a block of wood between the blade and mower
deck to prevent the blade from turning.
5. For the BLADE I, loosen the blade nut by turning it
clockwise (as viewed from bottom of mower) using a
15 mm wrench or socket (not provided). For the
BLADE II, loosen the blade nut by turning it counter
-clockwise (as viewed from bottom of mower) using a
15 mm wrench or socket (not provided).
6. Remove the blade nut, spacer, blade insulator, and
blade.
7. Make certain the motor assembly is pushed completely
against the motor shaft.
8. Place the new blade on the shaft against the motor
assembly. Ensure blade is properly seated with shaft
going through center blade hole and the two blade posts
inserted into their respective holes on the blade. Make
sure it is installed with the curved ends pointing up
toward the mower deck and not down toward the
ground. When seated properly, the blade should be flat
against the motor assembly.
9. Replace the blade insulator and spacer, then thread the
blade nut on the shaft and finger tighten.
NOTE: Make certain all parts are replaced in the exact
order in which they were removed.
10. For the BLADE I, torque the blade nut down counter
-clockwise using a torque wrench (not provided) to
ensure the bolt is properly tightened. For the
BLADE II, torque the blade nut down clockwise using
a torque wrench (not provided) to ensure the bolt is
properly tightened. The recommended torque for the
blade nut is 350-400 in. lbs.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks 25137 - 49Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks 25137 - 49Li in the language / languages: All languages as an attachment in your email.

The manual is 48,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info