Manual Greenworks 21227 (page 21 of 234) (All languages)

644732

Zoom out

Zoom in

1/234

English

FR DE ES IT PT NL SV DA NO FI

HU CS RU RO PL SL HR

HU C

ET LT LV SK BG

■Remove he spool from the cutting head.

NOTE: Remove any old cutting line remaining on the

spool.

■Cut a piece of cutting line approximately 3m long. Use

only 1.65mm diameter monofilament cutting line.

■Insert the cutting line into the anchor hole in the upper

part of the spool. Wind the cutting line around the upper

part of the spool clockwise, as shown by the arrows on

he spool. Place cutting line in the slot on upper spool

flange, leaving about 15cm. extended beyond the slot.

Do not overfill. After winding the cutting line, here

should be at least 0.635 cm between the wound

■Replace the spool, and the spool cover. Refer to spool

replacement earlier in this manual.

STORING THE TRIMMER

■Remove the battery pack from the trimmer before

storing.

■Clean all foreign material from the trimmer.

■Store it in a place that is inaccessible to children.

■Keep away from corrosive agents such as garden

chemicals and de-icing salts.

■Store and charge your batteries in a cool area.

Temperatures above or below normal room

temperature will shorten battery pack life.

■Never store batteries in a discharged condition. Wait

for battery pack to cool and fully charge immediately.

■Store the battery pack where the temperature is below

27˚C and away from moisture.

■All batteries gradually lose their charge. The higher the

temperature, the quicker they lose their charge. If you

store your unit for long periods of time without using

it, recharge the batteries every month or two. This

practice will prolong battery pack life.

TROUBLESHOOTING

cutting line and the outside edge of the spool.

Problem Possible cause Solution

String will not advance when using the

auto-feed head.

String is welded to itself. Lubricate with silicone spray.

Not enough string on spool. Install more string. Refer to string

replacement earlier in this manual.

String is worn too short. Pull string while pressing line release button.

String is tangled on spool. Remove string from spool and rewind. Refer

to string replacement earlier in this manual.

Grass wraps around shaft housing and

string head. Cutting tall grass at ground level. Cut tall grass from the top down to prevent

wrapping.

Motor fails to start when switch trigger is

depressed.

Battery is not secure.

To secure the battery pack, make sure the

latch on bottom of the battery pack snaps

into place.

Battery is not charged. Charge the battery pack according to the

instructions included with your model.

Shaft not connected completely.

Make sure lower shaft is fully seated in shaft

coupler on upper shaft and secure shaft

coupler.

DISPOSAL

This marking indicates that this product should not be disposed with other household wastes throughout

the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,

recycle it responsibly to promote the sustainable reuse of material resources. To return your used device,

please use the return and collection systems or contact he retailer where the product was purchased.

They can take this product for environmental safe recycling.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks 21227 in the language / languages: All languages as an attachment in your email.

The manual is 16,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Greenworks 21227 Manual

Product: