Manual Greenworks 20077 - G-MAX 40V DigiPro (page 21 of 256) (All languages)

644723

Zoom out

Zoom in

1/256

English

FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG

WARNING

Never operate the chain saw without suffi cient chain

lubrication as this might damage the saw and is a threat

to safety. Check he chain lubricant level before each use!

In order to prevent kickback, please follow these safety

instructions:

Never cut wi h the tip of the guide bar! Be careful when

continuing from previous cuts.

Always start cutting only when the chain saw is already

running.

Make sure that the saw chain is always properly

sharpened.

Never cut through more han one branch at a time!

When lopping off branches, be careful not to touch any

other branches.

When cross-cut ing, pay attention to trunks standing

very close to each other. If possible, use a sawing tres le.

HOLDING THE CHAIN SAW

Always hold the chain saw with your right hand at the

rear handle and your left hand at the front handle.

Grip both handles with the thumbs and

the handles. Ensure that your left hand is holding the front

handle so that your thumb is underneath.

STARTING OPERATION

OPERATING THE CHAIN BRAKE

Before

Press the on/off switch (item 44), his makes the

switch trigger operational.

starting for operation, you should install the

battery pack in the machine.

Start the machine: Press the Safety lock-off button (item

4), and then pressure the switch trigger (item 5).

STOPPING OPERATION

Release the power switch trigger (item 5) to stop the

chain saw.

USING THE CHAIN SAW

Always be sure of your footing and hold the chain saw

firmly with both hands while he motor is running.

BASIC FELLING, LIMBING, AND CROSS-CUTTING

TECHNIQUES See figure 9

See figure 22

See figure 8

See figure 11

endanger any person, strike any utility line or cause any

property damage. If the tree does make contact with

any utility line, the utility company should be notified

immediately.

The chain saw operator should keep on the uphill side of

the terrain as the tree is likely to roll or slide downhill after

it is felled.

An escape path should be planned and cleared as

necessary before cuts are started. The escape path

should extend back and diagonally to the rear of the

expected line of fall.

Before felling is started, consider the natural lean of the

tree, the loca ion of larger branches and the wind direction

to judge which way he tree will fall.

Remove dirt, stones, loose bark, nails, and staples from

the tree.

NOTCHING UNDERCUT (A NOTCH CUT IN A TREE TO

DIRECT THE FALL) See Figure 10

Make the notch 1/3 in diameter of the tree, perpendicular

to the direction of falls. Make the lower horizontal notching

cut first, this will help to avoid pinching of either the saw

chain or the guide bar when the second notch is being

made.

FELLING BACK CUT (THE FINAL CUT IN A TREE

FELLING OPERATION, MADE ON THE OPPOSITE SIDE

OF THE TREE FROM THE NOTCHING UNDERCUT)

See Figure 10

Make the felling back cut at least 50mm higher than the

horizontal notching cut. Keep the felling back cut parallel

to the horizontal notching cut. Make the felling back cut

so as to leave enough wood to act as a hinge. The hinge

wood keeps the tree from twisting and falling in the wrong

direction. Do not cut through he hinge. As the felling cut

gets close to the hinge, the tree should begin to fall. If

here is any chance that the tree may not fall in the desired

direction or it may rock back and bind the saw chain, stop

cutting before the felling back cut is complete and use

wedges of wood, plastic or aluminium to open the cut and

drop the tree along the desired line of fall. When the tree

begins to fall, remove the chain saw from the cut, stop the

motor, put the chain saw down, and then use the retreat

path as planned. Be alert of overhead limbs falling and

watch your footing.

LIMBING A TREE

Limbing is removing the branches from a fallen tree. When

limbing, leave the larger lower limbs to support the log off

the ground. Remove the small limbs in one cut. Branches

FELLING A TREE

When bucking and felling operations are being performed

by two or more persons at the same time, the felling

operation should be separated from the bucking operation

by a distance of at least twice the height of the tree being

felled. Trees should not be felled in a manner that would

Check the operating condition of the chain brake

prior to each use.

Engage the chain brake by rotating your left

hand around the front handle, allowing the

back of your hand to push the chain brake

lever/hand guard toward the bar while the

chain is rotating rapidly. Be sure to maintain

both hands on the saw handles at all times.

Reset the chain brake back into the RUN

position by grasping the top of the chain

brake lever/hand guard and pulling toward the front

handle.

WARNING

If the chain brake do not stop the chain immediately, or if

the chain brake will not stay in the run position without

assistance, take the saw to an authorized service center

for repair prior to use.

My chainsaw has not been used for a while and now doesn’t operate at all. The battery has been charged and and shows 40.2 volts
The saw has been stored indoors with battery kept separate.
Can you suggest what I can try to get it working. Submitted on 16-9-2023 at 17:23
Reply Report abuse
Chain keeps falling off as soon as pressure is applied when cutting. The actual chain guide moves up and tension is removed. Seems like the chain guide is not locating in the machine correctly? Submitted on 14-2-2022 at 04:18
Reply Report abuse
The chain oiling system has stopped delivering when tank is full of oil? Submitted on 13-12-2021 at 10:11
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks 20077 - G-MAX 40V DigiPro in the language / languages: All languages as an attachment in your email.

The manual is 8,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Greenworks 20077 - G-MAX 40V DigiPro

Greenworks 20077 - G-MAX 40V DigiPro Additional guide - All languages - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Greenworks 20077 - G-MAX 40V DigiPro Manual

Product: