505372
20
Zoom out
Zoom in
Previous page
1/25
Next page
Installing the indoor unit
20
Install the Rear Panel
1. Always mount the rear panel horizontally. As the water drainage pipe is on the left, when adjusting the
rear panel, this side should not be too high; the right side should be slightly higher.
2. Attach the rear panel to the selected
location.
3. Be sure that the rear panel has been
attached firmly enough to withstand
the 60 kg of weight. The weight
should be evenly shared by each
screw.
e pipe
Fig.1
all
e pipe
Fig.1
all
Wall
Left Right
Rear pipping holeRear pipping hole
Mark on the middle of it
Gradienter
Wall
Space to
the wall
150mm
above
Space to
the wall
150mm
above
Install the Piping Hole
Install the Water Drainage Pipe
Connect indoor and outdoor electric wires
1. Make the piping hole in the wall at a slight downward slant to the
outdoor side
2. Insert the piping-hole sleeve into the hole to prevent the connection
piping and wiring from being damaged when passing through the hole.
1. To ensure good drainage, the drain hose should be
placed at a downward angle.
2. Do not wrench or bend the drain hose or it will flood.
3. When the long drainage hose passe through the indoor
section, the insulation materials should be wrapped.
1. Lift the front panel up.
2. Unscrew off the fixing screw in the cover plate and remove the cover plate.
3. Put the power connection cable through the back of indoor unit wire hole and pull it through..
4. All the wiring should be connected according to the circuit diagram on the unit.
5. Place the power connection cable into the wire groove,
cover with the sheath and then the cover plate. Screw in the fixing screw and tighten the connection
wire.
6. Cover the front panel cover.
7. For the cooling and heating unit, the signal control wire can be passed through the indoor unit
connection. Use the wire clip that is under the body case, tighten the signal control wire.
Installation de unité intérieure
20
Installer le panneau arrière
1. Fixez toujours le panneau arrre à l’horizontale. Puisque le tuyau de drainage de l’eau se trouve à
gauche, le panneau arrière ne devrait pas être fi trop haut. Le droit devrait être légèrement sule.
2. Fixez le panneau arrière à l’endroit
désiré.
3. Assurez-vous que le panneau arrière
soit bien en place afin qu’il puisse
supporter 60 kg (132 lb) de poids. Le
poids devrait être réparti également
pour chacune des vis.
e pipe
Fig.1
all
e pipe
Fig.1
all
Mur
Gauche Droite
(trou pour les tuyaux
à l’arrière)
(trou pour les tuyaux
à l’arrière)
Indoor
Wrenched Bent
Flooded
Tordu Plié
Débordement
Wall pipe
Seal pad
Outdoor
Intérieur
Tuyaux
dans le mur
Coussin
d’étanchéité
Extérieur
Marque au milieu
Gradateur
Mur
150mm
d’espace
par
rapport
au mur
150mm
d’espace
par
rapport
au mur
Percer le trou pour les tuyaux
Installer le tuyau de drainage de l’eau
Raccorder les fils électriques à l’intérieur et à l’extérieur
1. Percez un trou dans le mur pour les tuyaux, avec une légère inclinaison
vers l’extérieur.
2. Insérez dans le trou le manchon à cette fin pour ne pas endommager le
tuyau et le fil de raccordement lorsqu’ils passeront dans le trou.
1. Pour faciliter le drainage, le tuyau devrait être
légèrement incliné.
2. Ne tordez ou ne pliez pas le tuyau de drainage,
car il débordera.
3. Lorsque le long tuyau de drainage passe à l’intérieur,
il devrait être revêtu de matériaux isolants.
1. Soulevez le panneau avant.
2. Dévissez les vis de fixation du panneau de revêtement et retirez ce dernier.
3. Insérez les fils électriques dans le trou pour les tuyaux de l’appareil interne situé à l’arrière et tirez
sur les fils.
4. Tous les fils devraient être raccordés selon le diagramme du circuit situé sur l’appareil.
5. Remettez le panneau de revêtement en place à l’aide des vis de fixation.
6. Rabaissez le panneau avant.
7. Pour les appareils de refroidissement et de chauffage, le fil de commande des signaux peut être
inséré dans l’appareil interne. Utilisez l’agrafe située sous le boîtier. Serrez le fil de commande des
signaux.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gree GWC-12KF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gree GWC-12KF in the language / languages: English as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info