505371
6
Zoom out
Zoom in
Previous page
1/18
Next page
6
6
INSTALLATION
CHOISIR L’EMPLACEMENT
Installez le climatiseur de niveau sur une
surface plane, dans un endroit dégagé (là
où les sorties d’air ne seront pas obstruées).
Pour un rendement maximal, prévoir un
dégagement minimal de 50 cm (20”) en
avant et derrière l’appareil (figure A).
840 mm
50 cm50 cm50 cm
450 mm
370 mm
130 cm (50”)
40 cm (16”)
INSTALLATION DU TUYAU
D’ÉVACUATION
Lorsque vous utilisez un climatiseur
mobile, le tuyau d’évacuation d’air chaud
doit être dirigé à l’extérieur de la pièce.
• En climatisation, ce tuyau doit être installé
en tout temps pour permettre à l’air chaud
généré par l’appareil d’être adéquatement
évacué à l’extérieur.
G
LISSEZ LEMBOUT CARRÉ DU TUYAU
D
ÉVACUATION SUR LA SORTIE DAIR CHAUD À
L
ARRIÈRE DU CLIMATISEUR (figure B).
INSTALLATION MURALE
• L’air chaud peut être évacué par une fenêtre,
une porte patio ou encore directement à
travers le mur.
1. Choisissez un mur extérieur, près duquel
l’appareil peut être installé adéquatement.
2. Dans le cas d’une installation murale, le trou
d’environ 13,3 cm (5-1/4”) doit être percé à
une hauteur variant entre 40 et 130 cm
(16” et 50”) à partir du plancher (figures C).
3. Installez l’embout du tuyau évacuation dans le
trou mural extérieur.
MUR
NOTE :
Le tuyau d’évacuation doit être aussi court et droit que
possible. Prenez soin de ne pas plier, tordre ou courber
le tuyau pour assurer une évacuation efficace et éviter
le retour d’air chaud vers le climatiseur (figure D). Pour
vous en assurer, tenez compte des directives suivantes :
• Placez le climatiseur le plus près possible de la sortie
d’air extérieur.
• Dévissez l’embout du tuyau, coupez l’excédent du
tuyau et ensuite revissez l’embout.
• N’oubliez pas de prévoir un dégagement de 50 cm
(20”) autour du climatiseur.
• Pour vous assurer d’un rendement maximal de votre
appareil, vous pouvez isoler le tuyau d’évacuation en
le couvrant d’une gaine d’isolation de 6” (non fourni).
INSTALLATION
CHOOSING THE LOCATION
Place the unit on a level surface in a cleared
out area where the air outlets cannot be
obstructed. For a maximum efficiency, keep
a clearance of at least 50 cm
(20”) front
and rear of the unit (Figure A).
FIXING THE EXHAUST HOSE
• During the operation of an air conditioner,
a large flow of hot air must be exhausted
out of the room. The exhaust hose
supplied with this air conditioner must be
connected at all times (when running in
air conditioning mode) to exhaust the hot
air out.
S
LIDE THE HOSE SQUARE ADAPTOR ALL THE WAY
DOWN OVER THE HOT AIR OUTLET ON BACK OF
THE UNIT
(Figure B).
WALL INSTALLATION
• The hot air must be exhausted outdoor
through a window, a patio door or directly
through the wall.
1. Pick an exterior wall where you will be able
to correctly install the air conditioner and the
hot air outlet.
2. Drill a hole of 13,3 cm (5-1/4”) on the
exterior wall. The hole must be 40 to 130 cm
(16” to 50”) above the floor (Figure C).
3. Fix the external end of the exhaust hose onto
the wall pre-drilled hole.
NOTE :
The hot air exhaust hose must be as short as
possible. To avoid hot air backdraft and
guarantee an efficient exhausting of the hot air,
make sure the hose is not bent, kinked or twisted
(Figure D). In order to do so, please check upon
the following :
• Position the air conditioner as close as
possible to the outside air outlet.
• Unscrew the hose connector, cut the excess
hose and screw the connector back on the hose.
• Do not forget to leave a 50 cm (20”)
clearance all around the air conditioner.
• To maximize the efficiency of the air
conditioner, you may insulate the exhaust hose
with a 6” insulating flexible tube (not included).
Figure A
Figure B
840 mm
50 cm50 cm50 cm
450 mm
370 mm
Figure A
Figure B
Figure C
Figure D
APPAREIL
130 cm (50”)
40 cm (16”)
MUR
Figure C
APPAREIL
Figure D
Note : le modèle peut différer de celui illustré.
Note : model may differ from illustration.
6


Need help? Post your question in this forum.

Forumrules
1

Forum

gree-13-04582

Reset search

  • Dear Sirs,

    I live in Montreal Canada. Where can I buy the replacement venting tube for my Gree 13-04582 unit please?

    Thank you
    Francis Submitted on 26-5-2020 at 18:14

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gree 13-04582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gree 13-04582 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info