716499
9
Zoom out
Zoom in
Previous page
1/13
Next page
have
an empty running
test.
(Detail
information please
find in
the motor manual
instrucíon.)
After
testing, it can
be
had
a test
with load from
slight to heavy. Do not
operate machine
with overload, it is
determined
by motor load.
If it is
overload,
immediately
reduce or
stop to draw
the materials in.
After
a
period
of regular
movement,
putting
into
production
under no unusual noise
or overheat
phenomenon.
Keep
the minors
away
from
the
spot.
Do not
put
hands
or other body
parts
into
hopper.
Do not
get
close
to discharge
port,
the chips
are expelled from
discharge
port
can
hurt
you
or may cause serious injury.
If
the
machine
makes
abnormal vibration
or unusual noises,
immediately
turn
the
machine
offand check it.
If there
aÍe
many
uncut materials,
blades may
be needed
to sharpen or intervals
are needed
to
make
adjustrnent. It
is easy
to cause injury
due to
blades are sharp
enough.
Sharpen or adjust
blades should
go
to indicate
maintenance
point.
The
recommendation
of blade intervals
is 2-3mm.
When the belt appear
damage or skid,
please
make
adjustrnent
or
replacement
as
follows,
1. Turn
offengine, loose
the
fixed
bolt
of belt
guard,
remove
the
belt coverll
after the machine are cooling,
2. Loose
the fïxed bolt
engine, steeling hand
wheell8
toward right
or
left
to
adjust
or
remove
belt.
3. Lock
the fixed
bolt of engine, fold
the folding hand
ofhand
wheel, and refit
the beltl
l.
6. Maintenance
instructions
This
series of
machine
is only
the marn
shaft bearing, which is needed
to infuse
lubricating
oil. After
a
period
of using, it is
necessary
to
infuse
the
grease.
How ofter
to
infuse
grease
is
determined by using
environment
and it's frequency. You
must
infuse
the
grease
after using 50 hours
because
the lackness
of
grease
can be
easily
caused
bearing damage. Check
all the
parts
regularly
with
l-2
times monthly
including
bearing,
blades, belt etc. Make
sure them
are
flexible
and
sharp. Replace
the blades
as soon as the chipping
performance
begins to deteriorate. The
blades are
needed
to check regularly. The
blunt
blades will lower
working
efficiency and cause
the damage of machine.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greatbull GBD-65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greatbull GBD-65 in the language / languages: English as an attachment in your email.

The manual is 3,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info