686177

GRE Bora Bora Manual

33
Zoom out
Zoom in
Previous page
1/48
Next page
FITTING THE SKIMMER FRAME (M):
En sure that all holes are lined up properly (seal to wall plate perforation to
skimmer). Screw 10 remaining screws loosely through the frame to check that
the fit is correct. Then tighten the screws a little more one by one in the order
indicated. Finally, tighten them fully in the same order. FINAL DETAILS: Clip
the trim cover over the skimmer frame (Z). Put the gate (K) into the skimmer
mouth and clip it in place by pressing the two ends. Fit the basket (O) inside the
skimmer and finally fit the skimmer body cover (TS). FINISH FILLING THE
POOL TO HALF WAY UP THE SKIMMER MOUTH TO ENSURE THAT THE
WATER ENTERS THE SKIMMERS.
COLOCACION DEL MARCO DEL SKIMMER (M) :
Asegurarse de que todos los agujeros estén uno frente a otro (junta-troquel
chapa-skimmer). Insertar los 10 tornillos que quedan a través del marco sin
enroscarlos demasiado para verificar el correcto encaje. Enroscar un poco los
tornillos, uno después de otro, siguiendo el orden indicado. AL FINAL
APRETARLOS FIRMEMENTE SIGUIENDO EL MISMO ORDEN. ULTIMOS
DETALLES:Colocar a presión la tapa embellecedora del marco del skimmer
(Z). Para acabar, introducir la compuerta (K) por la apertura rectangular (presionar
con delicadeza los dos extremos y encajar los salientes). Colocar el cesto (O)
en el interior del skimmer y la tapa del cuerpo del skimmer(TS).TERMINAR DE
LLENAR LA PISCINA HASTA LA MITAD DE LA PUERTA DEL SKIMMER,
(10 - 15 cm por debajo del borde de la piscina) PARA QUE ENTRE AGUA EN
SU INTERIOR Y LLENE EL SISTEMA DE FILTRACION.
INSTALLATION DU CADRE DU SKIMMER (M):
S'assurer que tous les trous se trouvent en face les uns des autres (joint-perçage
tôle-skimmer). Mettre les10 vis restants dans le cadre sans les serrer pour
s'assurer que l'emboîtement est correct. Serrer un peu les vis, l'une apres l'autre,
suivant l'ordre indique. FINALEMENT LES VISSER FORTEMENT DANS LE
MÊME ORDRE. DERNIERS DØTAlLS: Installer, par pression, l'enjoliveur du
cadre du skimmer (Z). Pour finir, positionner la porte du skimmer (K) dans
l'ouverture rectangulaire (appuyer délicatement sur les deux extrémités et
emboîter les ergots). Installer le panier (O) à l'intérieur du skimmer ainsi que
le couvercle (TS). TERMINER LE REMPLISSAGE DE LA PISCINE; JUSQU’¸
CE QUE L’EAU ARRIVE ¸ LA MOITI DE LA BOUCHE DU SKIMMER, AFIN
QUE L'EAU ENTRE À L'INTÉRIEUR DE CE DERNIER ET REMPLISSE LE
SYSTEME DE FILTRATION.
ANBRINGEN DE MERRAHMENS (M):
Stellen Sie sischer, dass alle Bohrungen genau gegenüber liegen (Dichtung-
Stanzrahmen und Blech-Skimmer). Legen Sie die 10 verbliebenen Schrauben
durch den Rahmen ein, ohne sie jedoch zu sehr anzuziehen, um die korrekte
Justierung zu überprüfen. Schrauben nacheinander und in der angegebenen
Reihenfolge etwas eindrehen. AM SCHLUSS IN DER ANGEBENEN
REIHENFOLGE FESTZIEHEN. LETZTE EINZELHEITEN: Zierleiste des
Skimmerrahmens (Z) einrasten. Skimmerklappe (K) durch die Skimmeröffnung
einführen, dabei auf die beiden Enden drücken und einrasten lassen. Korb (O)
in den Skimmer einsetzen und schließlich das Skimmerhäuse (TS) mit dem
Deckel verschließen. BECKEN ETWA BIS ZUR H LFTE DER
SKIMMER FFNUNG BEF LLEN, DAMIT DAS WASSER AUCH IN DAS
SKIMMERINNERE GELANGEN KANN.
COLLOCAZIONE DELL«INFISSO DELLO SKIMMER (M):
Assicurarsi she tutti i fori siano uno di fronte all'altro (guarnizione-stampo lamiera-
skimmer). Inserire le 10 viti che restano attraverso l'infisso senza avvitarle troppo,
allo scopo di verificare la corretta sistemazione. Avvitare un po' le viti, una dopo
l'altra, seguendo l'ordine indicato. PER FINIRE, STRINGERLE SALDAMENTE
SEGUENDO LO STESSO ORDINE. AVVERTENZE: Inserire a pressione il
coperchio abbellitore nella cornice dello skimmer (Z). Introdulle lo sportello (K)
dalla bocca dello skimmer e fare pressione sulle 2 estremità fino ad incastrarè
stesse. Sistemare il cestello (O) all'interno dello skimmer e ad ultimo, coperchio
del corpo dello skimmer (TS). ULTIMARE IL RIEMPIMENTO DELLA PISCINA
CON ACQUA FINO AD OLTREPASSARE MET¸ DELLA BOCCA DELLO
SKIMMER, IN MODO DI FAR RIENTRARE L'ACQUA ALL'INTERNO DELLO
STESSO.
PLAATSING VAN HET RAAM VAN DE SKIMMER (M):
Verzekert u zich ervan dat alle gaten met elkaar overeenkomen (pakking-
geponste opening-skimmer). De overgebleven door de lijst inbrengen zonder
deze al te schroeven om de correcte inpassing te kunnen verifiëren. De schroeven
de één na de ander een iets aanschroeven, de aangewezen volgorde volgende.
UITEINDELIJK DE SCHROEVEN STEVIG VATSCHROEVEN VOLGENS
DEZELFDE VOLGORDE. LAATSTE BIJZONDERHEDEN: Onder druk het
sierdeksel van het raam van de skimmer (Z) plaatsen, de deur (K) door de mond
van de skimmer inbrengen, druk uitoefenende op de twee uiteinden en deze
inpassen. De mand (O) plaatsen binnenin de skimmer en daarna het deksel
van de romp van de skimmer (TS). GEBRUIK HET DEKSEL VAN DE ZUIGER
(TA) ALLEEN ALS DE BODEMREINIGER GEBRUIKT WORDT. HET VULLEN
VAN HET ZWEMBAD VOLTOOIEN TOTAAN DE HELFT VAN DE SKIMMER,
OPDAT HET WATER NAAR BINNEN KAN STROMEN.
INSTALA O DO QUADRO DO SKIMMER:
Verificar se todos os furos estão enfrente uns dos outros (junta-peça furada
chapa-skimmer). Pôr os 10 últimos parafusos no quadro sem aparafusar muito,
para verificar se estão bem encaixados. Aparafusar pouco a pouco os parafusos,
um após o outro seguindo a ordem indicada.FINALMENTE, APERTAR
FIRMEMENTE SEGUINDO A MESMA ORDEM. ULTIMOS DETALHES: Instalar
o tampão do caixilho do shimmer (T) carregando nele. Introduzlr a válvula (K)
na boca do skimmer (carregar nas duas extremidades e encaixar). Instalar o
recipiente (O) no interior do skimmer e, por fim, colocar a tampa do corpo do
skimmer (TS). TERMINAL O ENCHIMENTO DA PISCINA AT A AGUA
CHEGAR ¸ METADE DA BODA DO SKIMMER, PARA QUE A AGUA POSSA
ENTRAR NO INTERIOR DO MESMO.
4 cm
OUT
IN
J
M
S
1º
10º 3º
4º
9º 2º
8º
6º
5º
7º
F
F
15 cm
AGUA
Nivel WATER
EAU
31
16
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GRE Bora Bora at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GRE Bora Bora in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info