Screw the upright support (PV) to the appropriate bottom and top joining-pieces with 3 T1 screws each. ENVELOPING JOINT PROTECTORS
B1: Introduce the enveloping joint protector (B1) through the top part of the vertical profile (PV), screw the profile in its inferior part and lower
the enveloping joint protector until it touch the floor.
Repeat this procedure until the half-circle is completed. Join the section-pieces together
and check by looking at the ribbing on the wall-plating that the upright supports are properly vertical.
NB: Check that the 3 + 3 (top and bottom) T1 screws are all fitted on each upright support and joining-piece all around the pool.
Fill the pool to
a depth of 2 cm of water and extend the liner to eliminate all wrinkles.If the water does not lie evenly over the whole of the pool bottom, the
ground is not level enough. Remove the liner and level the ground.
Atornille el perfil vertical (PV) con 3 tornillos T1 a la pieza de unión correspondiente que está en la parte inferior y con otros 3 tornillos a la
pieza de unión superior. BASES INYECCI N B1: Introducir la base de inyección (B1) por la parte alta del perfil vertical (PV),atornillar el perfil
en su parte inferior y bajar la base hasta apoyar en el suelo. Repita estos pasos hasta completar la media circunferencia, junte bien los perfiles
entre sí y compruebe que los perfiles verticales queden perfectamente verticales, para ello ayúdese de las lineas del perfilado que tiene
la chapa.
NOTA: Compruebe haber colocado todos los tornillos (T1) ( 3+3),arriba y abajo por cada perfil vertical y sus piezas de unión, en toda la piscina.
Llenar la piscina con 2 cm. de agua. Volver a extender la funda hasta eliminar todas las arrugas. Si se observase que el agua no se reparte
uniformemente sobre toda la superficie del fondo, esto es síntoma de que el terreno no se encuentra convenientemente nivelado. Retire la
funda y proceda a nivelarlo.
Vissez le profilé vertical (PV) avec 3 vis T1 à la pièce d'union correspondante qui se trouve dans la partie inférieure, et avec 3 autres vis à la
pièce d'union supérieure.
ENJOLIVEURS ENVELOPPANTS B1: Introduire l'enjoliveur enveloppant (B1) par la partie haute du profilé vertical
(PV), visser le profilé dans sa partie inférieure et baisser l'enjoliveur enveloppant jusqu'à ce qu'il touche le sol.
Répétez ce processus jusqu'à
la fin de la demi-circonférence; assemblez bien les profilés entre eux et assurez-vous que les profil s verticaux sont parfaitement verticaux.
Pour ce faire, suivez les lignes du profilé de la tôle.
NOTE: vérifiez si vous avez bien mis toutes les vis (T1) (3+3) au-dessus et au-dessous de chaque profilé vertical ainsi que les pièces d'union
dans toute la piscine. Remplissez le bassin d’environ 2 cm. d'eau. Fermez l’arrivée d’eau. Supprimez les plis en tendant le fond du liner vers la
paroi. Verifiez que l’eau se repartisse sur le fond, de maniere egale.
Verschrauben Sie das senkrechte Profil (PV) mit 3 Schrauben T1 am entsprechenden innen liegenden Verbindungsstück mit weiteren 3 Schrauben
am oberen Verbindungsstück. KUNSTSTOFFEINSPRITZSTTZEN B1: Kunststoffeinspritzstützen B1 von oben in das Senkrechtprofil (PV)
einführen, Profil am unteren Ende anschrauben und Stütze auf dem Boden befestigen. Wiederholen Sie diese Schritte, bis der Halbkreis
vollständig zusammengesetzt ist, verbinden Sie die Profile untereinander und sellen Sie sicher, da§ die senkrechten Profile einwandfrei
lotrecht stehen. Als Wegweiser dazu dienen Ihnen die Profillinien des Blechs.
HINWEIS: Stellen Sie sicher, daß alle Schrauben (T1) (3+3) oben und unten an jedem senkrechten Profil und seinen Verbindungsstücken am
ganzen Pool eingesetzt sind.
Füllen Sie ca.2 cm. Wasser in das Becken. Strecken Sie das Liner wieder, um alle noch vorhandenen Falten zu
entfernen. Sollte das Wasser den Boden nicht gleichmäßig bedecken, so deutet dies darauf hin, daß der Untergrund nicht einwandfrei nivelliert
ist. Nehmen Sie dann das Becken-Liner wieder ab und nivellieren Sie den Untergrund.
Avvitare il profilato verticale (PV) con 3 viti T1 al relativo pezzo di unione che si trova nella parte inferiore e con altre 3 viti al pezzo di unione
superiore.
BASI INIEZIONE B1: Introdurre la base a iniezione (B1) dalla parte alta del profilo verticale (PV), avvitare il profilo sulla relativa parte
inferiore ed abbassare la base sino a poggiare sul suolo.
Ripetere questi passaggi fino a completamento di metà circonferenza, unire bene i
profili l'un l'altro e verificare la perfetta verticalit dei profilati verticali. A questo fine, usufruire delle linee di profilato della lamiera.
NOTA: verificare la collocazione di tutte le viti (T1) (3+3), sopra e sotto in ogni profilato verticale e loro pezzi di unione in tutta la piscina.
Riempire
la piscina con 2 cm d’acqua. Tendere nuovamente la guaina fino ad eliminazione completa di tutte le pieghe. Qualora si rilevasse che l’acqua
non si distribuisce uniformemente su tutta la superficie del fondo, ciò significa che il terreno non è del tutto livellato. Togliere la guaina e provvedere
al livellamento del medesimo.
Schroef het verticale profiel (PV) met 3 schroeven T1 op het overeenkomstige aansluitstuk aan de onderkant vast en met 3 andere schroeven
op het bovenste aansluitstuk.
BASES INJECTIE B1: De injectiebasis (B1) inbrengen aan de bovenkant van het vertikale profiel (PV), het profiel
aan de onderkant aanschroeven en de basis naar beneden brengen en op de grond laten rusten.
Herhaal deze stappen tot de halve cirkel werd
vervolledigd. Zet de profielen onderling goed tegen elkaar en controleer of de verticale profielen perfect verticaal komen te staan. Maak
hiervoor gebruik van de profielmarkeringen op de plaat.
OPMERKING: Controleer of u alle schroeven (T1) (3 + 3) boven- en onderaan voor elk verticaal profiel met zijn aansluitstukken overal op het
zwembad heeft geplaatst.
Vul het zwembad met water tot op een hoogte van 2 cm. Trek het zeil opnieuw strak tot alle plooien verdwenen zijn.
Stelt u vast dat het water niet gelijkmatig over het volledige bodemoppervlak wordt verdeeld, dan wil dat zeggen dat het terrein niet goed waterpas
staat. Haal het zeil weg en maak de ondergrond waterpas.
Aparafuse o perfil vertical (PV) com 3 parafusos T1 à peça de união correspondente que está na parte inferior e, com mais 3 parafusos à peça
de união superior.
BASES INYECO B1: Introduzir a base de injecção (B1) pela parte alta do perfil vertical (PV), aparafusar o perfil na parte
inferior e baixar a base até se apoiar no chão.
Repita este procedimento até acabar meia circunferência; junte bem os perfis entre eles e
assegure-se que os perfis verticais ficaram perfeitamente verticais. Para isso, siga as linhas de perfilado da chapa.
NOTA. Verifique se colocou todos os parafusos (T1) (3+3), em cima e em baixo de cada perfil vertical e as peças de união em toda a piscina.
Encher a piscina com 2 cm de água. Esticar novamente a bainha até eliminar todos os vincos. Se a água não se distribuir de modo uniforme
por toda a superfície do fundo, quer dizer que o terreno não está bem nivelado. Tirar a bainha e nivelar.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for GRE Bora Bora at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of GRE Bora Bora in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.
The manual is 5,36 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
