637243
15
Zoom out
Zoom in
Previous page
1/30
Next page
place it as closer to center position as possible. Be sure the steering trim on the transmitter
at the neutral position.
Trim Operation And Maximum Trav
Changing the trim can effect the overall settings, when adjustments are made with the trims,
please recheck your installation for maximum servo travel (Steering EPA right side and left
side).
When Trim movement goes to extremes
That means if you make a lot of trim movement to get a servo to the neutral position, please
reposition the servo horn or servo saver on the servo and inspect your linkage installation.
15 94001 GM-Racing XG-6i Race Spec Instructions
English
SERVICE AND REPAIR
In problem cases, or for questions and repairs, please contact:
GRAUPNER-Service, Henriettenstrasse 94-96, D-73230 Kirchheim/Teck,
Tel. +49/1805/472876
Gastrimmung (TH.TRIM)
Throttle neutral adjustments can be made by moving the throttle trim to the left or the right.
Racers Tip
When using a electronic speed control, please set the throttle trim to neutral and make adjust-
ments to the speed control. On a gas powered model, set the trim to neutral and adjust the
linkage to the point where carburetor is fully closed in accordance with the engine instruction
manual.
Trim Operation and Travel
Trim adjustments will effect the overall servo travel, so please check the (backward)
movement after the adjustment
When trim movement is goes to extremes
That means if you make a lot of the trim movement to get the servo to the neutral position,
please recenter the servo horn closer to the neutral position and inspect your throttle
linkage.
TECHN. DATA TRANSMITTER: RECEIVER:
Frequency............................. 2.4 Ghz DSSS....................... 2.4 Ghz DSSS
Power Requirement................8.7 – 12 V DC........................ 4.8 - 5.6V DC
Channels...............................3.......................................... 3
Current Drain........................ ca. 300 mA (9,6V).................. ca. 14 mA
ST.D/R range......................... 0% - 120%
Temperature (working)...........0° ~ +70° C
Spare parts:
94000.1 Receiver 2,4Ghz for XG-6i
94000.2 Binding-Plug for XG-6i Receiver
94000.3 Receiver - Antenna 2,4Ghz
94000.6 Antenna 2,4Ghz für XG-6i Transmitter
94000.10 Micro Receiver 2,4Ghz for XG-6i
LIABILITY FOR PRINTING ERRORS EXCLUDED!
WE RESERVE THE RIGHT TO INTRODUCE MODIFICATIONS!
4. SERVOREVERSE (REV)
This function reverses the direction of operation of the servos
related to transmitter steering, throttle, and channel 3 operation.
1. Press “ENTER” to see FUNCTION MENU.
2. Press “+” or “-“ to choose REVERSE, and press “ENTER” to
enter REVERSE adjusting interface.
3. Press “ENTER” to choose each Channel.
4. Press “+” to increase and “-” to choose “REV” or “NOR”.
5. Press “EXIT”to save your setting and leave REVERSE
interface, and back to the function menu interface.
Note:
However, when the position set by trim or sub trim shifts from the center, the center
becomes the opposite side.
TERMS: ST-STEERING, TH-THROTTLE,AUX-AUXILLIARY
94001 GM-Racing XG-6i Race Spec Instructions 04
English
2. STEERING RANGE (ST.D/R)
D/R is used to change the action range of steering servo when turning the steering wheel.
Increasing D/R will make the steering wheel action more sensitive. --D/R adjusting value
range: 0~120%, POS0 default value is 100%,POS1 default value is 70%. -- Press the ST.D/R
dial to select POS0 or POS1, and the value will display in the LCD when it is on the main
screen.
1. Press “ENTER” to see FUNCTION MENU.
2. Press “+” or “-“ to choose D/R, and press “ENTER” to enter D/R adjusting inter-
face.
3. Press “+” to increase and “-” to decrease D/R value.
4. Press “EXIT” to save your setting and leave D/R interface, and back to the function
menu interface.
TERMS: POS-POSITION
3. SUB-TRIM (S_TRIM)
Use this function to adjust the neutral position of the steering
and throttle servos. SUB TRIM adjusting value range: -100 -
100. Default is 0.
1. Press “ENTER” to see FUNCTION MENU.
2. Press “+” or “-“ to choose TRIM, and press “ENTER”
to enter SUB TRIM adjusting interface.
3. Press “+” to increase and “-” to decrease SUB TRIM
value.
4. Press “EXIT”to save your setting and leave SUB TRIM interface, and back to the
function menu interface.
TERMS: ST-STEERING, TH-THROTTLE
94001-eng.indd Druckbogen 5 von 10 - Seiten (16, 5)94001-eng.indd Druckbogen 5 von 10 - Seiten (16, 5) 19.01.2009 08:02:4719.01.2009 08:02:47
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner XG-6i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner XG-6i in the language / languages: English, German, French as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info