637245

Graupner Ultramat 18 - 6470 Manual

34
Zoom out
Zoom in
Previous page
1/92
Next page
34
INC
________________
________________
DEC
INC
+
-
DEC
INC
+
-
ENTER
DEC
DEC
INC
ENTER
Ni-MH discharge program
________________
________________NiMH discharge
1.00A 4.8V
DECINC
+
-
DEC
INC
+
-
ENTER
Ni-MH conditioning program
The typical purpose of this program is to determine the
residual capacity of a transmitter, receiver or drive battery,
or to discharge the pack to a defined level.
In this program the charger discharges the pack using the
set discharge current (0.1 ... 5.0 A, left of screen) until its
voltage falls to the set final discharge voltage (0.1 ... 36.0 V,
right of screen).
The set final discharge voltage should be a value of around
1.0 ... 1.2 V per cell, in order to avoid the pack becoming
deep-discharged. Deep-discharging a pack runs the risk of
reversing individual cells, i.e. they exhibit reversed polarity.
This program is designed to optimise the capacity of a
battery, and balance the state of its cells.
At top right you can use the INC or DEC button to determine
whether the conditioning program is to start with a charge or
discharge cycle. After this you set the number of cycles
from 1 to 5 (e.g., if you set three cycles, the pack will be
charged and discharged three times). The program dis-
charges the battery using the set discharge current stated
on the right of the screen (0.1 ... 5.0 A), and then recharges
it using the charge current (0.1 ... 20.0 A) shown on the left
of the screen. The charge process is terminated
automatically in accordance with the values already set for
„Ni-MH Delta Peak cut-off voltage“. The discharge cut-off
voltage is set in the Ni-MH discharge program. The method
of reading out the values for the actual cycle is described in
the section „Screen displays“.
or
NiMH cycle C>D 1
C:2.5A
D
:1.00A
Ni-MH manual program
________________
________________NiMH manual
C:2.5A
DECINC
+
-
Select this program when you simply wish to recharge a
battery using the set charge current. You can adjust the
charge current using the INC / DEC buttons, but only
before you connect the pack for charging. The range
available is 0.1 A to 20.0 A.
Never use a maximum charge current higher as the value
described in the battery instruction, never higher as 2C!
Never charge transmitter batteries with more as 2A!
f. e. a 4.2Ah battery should be limited to max. 4.2A.
The charge process is terminated automatically in
accordance with the values already set for „Ni-MH Delta
Peak cut-off voltage“.
… 34 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner Ultramat 18 - 6470 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner Ultramat 18 - 6470 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info